background image

)NSTALLATION'UIDE

10/100 PCI Network Interface Card Model FA311 v2

Estimated Completion: 10 minutes.

Start Here

Follow these instructions to install the NETGEAR FA311 v2 PCI Adapter in a computer 
with the Windows Vista, Windows XP or Windows 2000 operating system with the latest 
service pack.

Note:

 If you are working with a new installation, decide on a name for your network and 

for each PC. The whole network must have the same network name, while each PC must 
have a unique name. For detailed instructions, see the Windows manual, online help, or 
support. 

1. First, install the Ethernet adapter. 

a.

Shut down the computer.

b.

Unplug the computer power cord, and open the case.

c.

Locate an available PCI slot (check your computer’s manual to determine which 
slots are the PCI slots) and remove the corresponding back plate from the PC 
chassis.

Caution: 

Touch a grounded metal object such as the power supply to free yourself of 

static electricity before you handle the network card. To avoid damaging any 
components on the NETGEAR FA311 v2 PCI Adapter, handle it by the edges.

d.

Insert the FA311 v2 into the PCI expansion slot. Make sure that the card is fully 
inserted.

e.

Fasten the card to the rear of the computer chassis by tightening the screw that is 
on the PC.

f.

Close the case, plug the power cord back in, and restart your computer.

2. Next, connect the network cables.

Use Ethernet cable to connect a switch or hub to the NETGEAR FA311 v2 PCI 
Adapter.

The port on the card performs autonegotiation and supports full-duplex operation.

Warning: 

Windows detects the Ethernet adapter, and automatically installs a driver 

based on its chipset. You must update that driver to work with the NETGEAR 
NETGEAR FA311 v2 PCI Adapter.

3. Then, use Windows Device Manager.

Note:

 Windows dialog box displays may vary from one computer to another, but 

Windows should prompt for the same information. If a Windows compatibility 
warning window pops up, select Continue Anyway.

a.

Go to System Properties for the NETGEAR 
FA311 v2 PCI Adapter. To do this go to the 
Windows Start menu, select Control Panel, and 
double-click System; or right-click My 
Computer on the desktop and select Properties.

b.

Click the Hardware tab, and then click the 
Device Manager button.

c.

From Device Manager, double-click Network 
adapters, and then double-click your network 
adapter card. 

The network adapter that Windows selected 
depends on the operating system. In most cases, 
the following will be displayed:

Windows XP: 

RealTek RTL8139 Family PC 

Fast Ethernet NIC

Windows 2000: 

RealTek RTL8139(A)-based 

PCI Fast Ethernet Adapter

Windows Vista

: NETGEAR FA311v2 PCI 

Adapter.

d.

In the Properties dialog box, click the 
Driver tab.

e.

Click the Update Driver button.

4. Next, use the Windows Hardware Update Wizard

The Hardware Update Wizard window opens, 
as shown to the right.

a.

Insert the 

NETGEAR Resource CD

. This 

CD contains drivers for NETGEAR 
Ethernet adapters. If the CD main menu 
appears, close or minimize the window.

b.

Choose to install the driver from a list.

c.

Follow the wizard prompts to locate the 
driver on the 

NETGEAR Resource CD

 

and select it. 

d.

When the wizard is finished, remove the 

NETGEAR Resource CD

 from your 

computer.

Note: 

If the driver is not installed 

properly, there is an exclamation point 
next to the adapter in Device Manager. 
Reboot the PC and if the exclamation 
mark is still there, repeat the software driver update process from Step 3. If the 
problem persists, contact NETGEAR Technical Support.

Reviews: