background image

6-794

1

Rev. 06/06/03

6-794

Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement 

and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.

1" DRIVE   HEAVY DUTY

IMPACT WRENCH 

w/6" Ext. Anvil

Llave de impacto con agujero de torsión de 25.4 mm (1")

THIS INSTRUCTION

MANUAL CONTAINS
IMPORTANT SAFETY

INFORMATION

READ CAREFULLY AND

UNDERSTAND ALL

INFORMATION BEFORE

OPERATING THIS TOOL!

SAVE THIS MANUAL 

FOR FUTURE REFERENCE.

LAS INSTRUCCIONES EN

ESPAÑOL COMIENZAN EN

LA PÁGINA # 8.

ESTE MANUAL DE

INSTRUCCIONES 

CONTIENE IMPORTANTES

INFORMACIONES DE

SEGURIDAD

¡LEA CUIDADOSAMENTE 

Y ASEGÚRESE DE 

COMPRENDER TODAS

ESTAS INFORMACIONES,

ANTES DE PROCEDER 

CON EL FUNCIONAMIENTO

DE ESTA HERRAMIENTA!

CONSERVE ESTE MANUAL

PARA TENER UNA 

REFERENCIA EVENTUAL.

Se sabe que el polvo generado por el lijado, la aserradura, el esmerilado, la
perforación mecánica y por otras actividades de construcción contiene químicos
que producen cáncer, malformaciones congénitas u otros daños relacionados
con la reproducción. Algunos ejemplos de estos químicos son:

•  Plomo de pintura a base de plomo,
•  Sílice cristalina de ladrillos y cementos y otros productos de mampostería, y 
•  Arsénico y cromo de maderas tratadas químicamente.

El riesgo ante estas exposiciones varía, dependiendo de cuan frecuente usted
haga este tipo de trabajo. Para reducir la exposición a estos químicos: trabaje
en espacios bien ventilados, y trabaje con equipos de seguridad aprobados,
tales como las mascarillas contra el polvo diseñadas específicamente para
detener partículas microscópicas.

Summary of Contents for 6-794













Reviews: