◈
MXN22C Camera
◈
Installation
◈
Features
◈
Technical Specifications
* Design And Specifications Are Subject To Change Without Notice.
1. Before making the connection, disconnect the ground terminal from the battery
to avoid short circuits.
2. The plugs should be fully inserted into the connectors or jacks.
A loose connection may cause malfunctioning of the unit.
3. A damaged cable may affect the operation of the camera and may even cause
a malfunction of the camera or monitor: Avoid a damaged cable!
4. Protect the cable by using a guide tube, pipe or run the cable inside the vehicle
as much as possible. Caution! Run the cable in natural shapes in order to
prevent cable breaks.
5. Preferably use an acid free grease in between the waterproof screw type
connectors and tighten them firmly eachother.
▪
Caution !!
▪
Securing cable connection
Note!
The warranty will not be valid if the problem is related to moist / corrosion in the connector.
▪
Front View
▪
Rear View
Camera Bracket x 1
Manual x 1
Camera x 1
Screw kit x 1
IR LED’s
Day/Night sensor
1.
Match the arrow marks and
press the connectors together.
2. Screw the camera connector
up clockwise.
3. Tighten cable connection firmly
in order to prevent water ingress.
▪
Wiring to Monitor
Run the cable from the camera to the
monitor.
Extension cable
(Not supplied)
Instruction Manual
130 Degree Wide View, Autoheated, Color Camera
MXN22C
Heater function
(9~12V DC)
Audio out
Video out
Power (9~48V DC)
GROUND
Camera pin configuration
▪
Camera Assembly
1. Fix the supplied camera bracket to the vehicle.
2. Fix the bracket with camera according to drawing.
3. Adjust the viewing angle of the camera and fasten the screws firmly.
▪
Cable grommet
Drill a suitable hole (approx. Ø 19mm) and insert the
cable grommet.
Just before final fixation, please apply a proper sealant
(for prevention) between the hole and the grommet and
also between the cable and the grommet.
Monitor
Built-in Microphone
Normal/Mirror Image
switch
◈
Contents
Image Sensor :
1/3.2” Color SONY CMOS(
Exmor)
Picture elements :
PAL, 1.23Mega pixels(1280x960)
Resolution : 750TV lines
S/N ratio : Minimum 45dB (at AGC off)
Minimum illumination :
0 Lux (IR LED’s on)
Power range : DC 9 ~ 48V
Power consumption : DC 12V, 265mA (heater on)
DC 12V, 165mA (heater off)
Operating temperature : -40ºC to +80ºC
Viewing angle :
130˚(D) x 102˚(H) x 76˚(V)
Dimension : Ø 52mm, 72(W) x 51(D) x 63(H) incl. bracket
Weight :
Supplied Accessories :
Approx. 215g
Camera Bracket (1)
Stainless M6 x 25mm bolt + M6 nut (2 + 2)
Stainless M3 x 12mm bolt + M3 nut (2 + 2)
Stainless M4 x 16mm tapping screw (2)
Rubber stainless metal washer (2 + 2)
Rubber O-Ring (2)
Allen wrench 3mm (1)
▪
Best picture quality (in combination with Digital LCD monitor)
▪
High resolution CMOS camera (1.23Mega pixels)
▪
1/3.2” Color CMOS high resolution image sensor
▪
IP69K Waterproof Rating
▪
Built-
in IR LED’s
▪
Diagonal 130˚ viewing
▪
Normal/Mirror Image adjustable
▪
Built-in Microphone (for one-way audio)
▪
Multi purpose (Frontview, sideview, rearview, surveillance, etc)
▪
Built-
in Automatic Heater (below +10˚C)
▪
Anti-corrosive 3-fold coating
▪
Temp. -
40˚C ~ 80˚C
▪
Vibration resistant
▪
CE and EMC approved
Optional versions of model MXN22C:
MXN22C-078
78
˚(D) x 62.0˚(H) x 45.0˚(V)
MXN22C-040
40
˚(D) x 30.9˚(H) x 23.2˚(V)
MXN22C-020
20
˚(D) x 17.0˚(H) x 12.8˚(V)
10R-05-6368
E
9
M3 bolt
M6 nut
Metal washer
Rubber washer
Rubber O-ring
M3 nut
M6 bolt
Installation surface
Ø 6mm Drilling holes
