background image

A152400F-BF4 / A152400S-BF4 

TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER: 

1.800.591.9360

Technical Assistance Fax: 1.626.855.4894

LIMITED EXPORT WARRANTY - 

One year on parts only. 

Murdock warrants that its products are free from defects in material or workmanship under normal use and 
service for a period of one year from date of install or for 18 months after the date of shipment from the factory, 
whichever comes first. Murdock’s liability under this warranty shall be discharged solely by replacement or repair 
of defective material, provided Murdock is notified in writing within one year from date of shipment, F.O.B. 
Industry, California. 

This warranty does not cover installation or labor charges and does not apply to materials, which have been 
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the 
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this 
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges 
caused by defects in the materials, or any delay in the repair or replacement thereof.  This warranty is in lieu of all 
other warranties expressed or implied. Product maintenance instructions are issued with each unit and disregard 
or non-compliance with these instructions will constitute an abnormal use condition and void the warranty. 
Stainless steel must be protected on job site during construction and must be properly maintained after the water 
has been introduced into the water cooler or drinking fountain, or Murdock’s limited warranty is void.

LIMITED WARRANTY - UNITED STATES & CANADA

NOTES TO INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished. 
2. Please read this entire booklet before beginning the installation. 
3. Check your installation for compliance with plumbing, electrical and other applicable codes.

COMPLIES 

WITH

7021-023-001   

 Date: 10/28/2020

Test rating conditions are
compliant with ARI 1010.

Federal
Public Law
111-380 
(No Lead)

Murdock assumes no responsibility for use of void or 
suspended data. © Copyright Murdock, City of 
Industry, CA Member of  Morris Group International. 
Please visit 

www.murdockmfg.com 

for most 

current specifications.

A152-VR-BF4 Series

Barrier Free, Bi-Level, Wall Mounted Drinking Fountain with

Semi-Recessed Sensor Operated Bottle Filler and 32” Trim Panel 

Member of

15125 Proctor Ave, City of Industry,

CA, 91746 U.S.A.

Phone 800-591-9360

626-336-4561

Fax 626-855-4894

www.murdockmfg.com

 

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAINS

 

Summary of Contents for A152-VR-BF4 Series





















Reviews: