background image

CHAPTER 1

INTRODUCTION

1-1

The Micro ATX IR2 mainboard  is a high-performance personal computer
mainboard based on the AMD Athlon

®

 processor.  This mainboard provides

onboard Creative

®

 ES1373 PCI technology in audio. The AMD Athlon

®

processor is the newest microprocessor in the AMD K86

TM

 family of

microprocessors.

The mainboard uses the highly integrated AMD

®

 751  system controller  and

AMD 756 peripheral controller.  The AMD-751 system controller features:
the S2k system interface supports a 100Mhz clock and double-data rate
(DDR) transfers, the 33MHz 32-bit bus interface supports up to three
masters, the 66MHz AGP 1.0 compliant interface supports 2x data transfer
mode, and High Speed memory designed to support a 100MHz SDRAM (PC-
100-compatible-DIMM) with serial presence detect(PSD).  The AMD-756
peripheral bus controllers feature an integrated ISA bus controller,  an
enhanced IDE controller with Ultra DMA-66 support, and a keyboard/mouse
controller.

The MS-6191 ATX IR2 mainboard is one of our system board to implement
the AMD-750 chipset (AMD-751 and AMD-756), which supports a single
Slot A for AMD Athlon

®

 processor.

Chapter 1

INTRODUCTION

Summary of Contents for MS-6191 Micro ATX IR2























































































Reviews: