![background image](http://html.mh-extra.com/html/motorola/hmn4079/hmn4079_installation-and-operation-manual_245157001.webp)
(Continued on Back)
DESCRIPTION
The Mobile Keypad Microphone (Mic), Motorola
®
Kit Number
HMN4079_ is a full keypad handheld microphone. The keypad on
this microphone is intended to assist in navigating through the
menus on its parent device, as well as entering information such
as phone numbers and menu picks.
INSTALLATION
1.
Refer to illustration below and attach hangup clip (1) to
vehicle using the two sheet metal screws and back-up plate
provided. Place back-up plate (4) behind dashboard. Use flat-
head screw (2) in top mounting hole and hex-washer screw
(3) in bottom mounting hole. Be certain mounting screws
fasten into holes in back-up plate.
2.
Insert button on rear housing of Mic into hang-up clip.
3.
Insert the GCAI plug on the radio end of the Mic cord into the
GCAI jack on the front of the radio.
4.
Turn the locking collar on the radio end of the Mic cord 1/4
turn clockwise to secure it in place.
DISCONNECTING MIC FROM RADIO
1.
Turn the locking collar on the radio end of the Mic cord 1/4
turn counter clockwise.
2.
Pull cable from GCAI connector to release.
OPERATION
Press PTT switch before speaking into Mic. Position Mic about 1-
inch away from mouth and speak into Mic in a normal voice.
TROUBLESHOOTING
Troubleshooting of Mic is limited to determining whether the
inoperable condition of a Mic is caused by a faulty Mic Cord or a
faulty Mic Head. To make this determination and correct the fault,
replace the Mic Cord with the spare first. If replacing the Mic Cord
does not restore operation, replace the Mic Head. The Mic Cord
and Mic Head are not repairable items, therefore they must be
replaced when they are determined to be faulty.
REPLACING MIC CORD
Removing Cord from Mic Body
1.
Refer to illustration on next page. Grasp locking collar and,
while pushing it firmly towards Mic body, turn it counterclock-
wise 1/4 turn to disengage it from Mic body.
2.
Disconnect cord from Mic body by pulling TELCO connector
(which has no tab on it) out of TELCO jack on circuit board
inside Mic body.
Installing Cord Into Mic Body
1.
Slide locking collar on Mic end of cord away from TELCO
plug and past strain relief on cord.
2.
Orient TELCO plug on Mic end of cord so that it aligns with
TELCO jack inside Mic body and its contacts face rear of Mic
housing.
3.
Pass TELCO plug through hole at bottom of Mic body and
plug it into TELCO jack on circuit board inside Mic body.
4.
Slide locking collar back up on cord with tabs on its sides
facing sides of Mic body.
5.
Push locking collar firmly into hole at bottom of Mic body then
turn it 1/4 turn clockwise to secure it in place.
ITEM
NUMBER
MOTOROLA
PART NUMBER
DESCRIPTION
1
0180757T98
Hang-up Clip
2
0312002C01
Flat-Head Screw
3
0312002A01
Hex-Washer Head Screw
4
0780257N01
Back-up Plate
Vehicle
Dashboard
4
1
2
3
MAEPF-26073-O
*6881097C72*
6881097C72-P
MOBILE MICROPHONE
MOTOROLA KIT NO. HMN4079_
© 2005, 2006 by Motorola, Inc.
8000 W. Sunrise Boulevard, Ft. Lauderdale, FL 33322.
b
and MOTOROLA are trademarks of Motorola, Inc.
TELCO is a trademark of TELCO Intercontinental Corporation.
M
European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive The European Union’s WEEE directive requires that
products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the
WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and
electrical equipment or accessories in household waste. Customers or end-users in EU countries should contact their local equipment supplier
representative or service centre for information about the waste collection system in their country.