Monessen Hearth Direct Vent Gas Fireplace BDV300 Скачать руководство пользователя

Страница: 1 / 68

540700
BDV cover

MODELS:

BDV300, BDV400, BDV500, BDV600

BDV Series

Direct Vent Gas Fireplace

WARNINGS

IF thE INFORMAtION IN thESE INStRuctIONS ARE

NOt FOLLOWED ExActLy, A FIRE OR ExpLOSION

MAy RESuLt cAuSING pROpERty DAMAGE,

pERSONAL INjuRy OR LOSS OF LIFE.

– Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

– WhAt tO DO IF yOu SMELL GAS
• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the

fire department.

– Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

WARNING: Improper installation, adjustment,

alteration, services or maintenance can cause injury or

property damage. Refer to this manual. For assistance

or additional information consult a qualified installer,

service agency or the gas supplier.

This appliance may be installed in an aftermarket*,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

this appliance is only for use with the type of gas

indicated on the rating plate. this appliance is

not convertible for use with other gases, unless a

certified kit is used.

* Aftermarket: Completion of sale, not for purpose of resale,

from the manufacturer.

DuE tO hIGh tEMpERAtuRES, thE

AppLIANcE ShOuLD BE LOcAtED

Out OF tRAFFIc AND AWAy FROM

FuRNItuRE AND DRApERIES.
chILDREN AND ADuLtS ShOuLD

BE ALERtED tO thE hAZARDS OF

hIGh SuRFAcE tEMpERAtuRE AND

ShOuLD StAy AWAy tO AVOID BuRNS

OR cLOthING IGNItION.
y O u N G c h I L D R E N S h O u L D B E

SupERVISED WhEN thEy ARE IN thE

SAME ROOM AS thE AppLIANcE.
cLOthING OR OthER FLAMMABLE

MAtERIAL ShOuLD NOt BE pLAcED ON

OR NEAR thE AppLIANcE.
KEEp thE ROOM AREA cLEAR AND

FREE FROM cOMBuStIBLE MAtERIALS,

GASOLINE, AND OthER FLAMMABLE

VApORS AND LIquIDS.

READ BEFORE INStALLING. SAVE thESE INStRuctIONS

54D0700 1/09 Rev. 14

Installation and Operating Instructions

Содержание Direct Vent Gas Fireplace BDV300





































































Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды

Monessen Hearth Direct Vent Gas Fireplace BDV300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Direct Vent Gas Fireplace BDV300

Отзывы:

Похожие инструкции для Direct Vent Gas Fireplace BDV300

Бренды по названию

Популярные бренды