MINELAB ML 100 HEADPHONES
Minelab ML 100 headphones use aptX™ Low
Latency technology, which delivers faster, higher
quality audio than standard Bluetooth, so it will give
more precise and faster detection responses when
used for metal detecting.
They contain the latest CSR8670 chipset with aptX
and aptX Low Latency, and are compatible with
devices that support Bluetooth.
PACKAGE CONTENTS
•
ML 100 Headphones
•
3.5 mm (1/8 inch) Detachable Auxiliary Cable
•
USB Charging Cable
•
Instruction Manual
GETTING STARTED
1.
Ensure the Bluetooth headphones are
fully charged.
2.
Pair the charged Bluetooth headphones with a
Bluetooth enabled device.
BUTTONS AND INDICATIONS
CHARGING THE HEADPHONES
Connect the USB charging cable to charging USB
socket
5
of the headphones. The Status LED
4
will remain solid red during charging. When charging
is complete, the Status LED
4
will turn solid blue.
NOTE: USB Charger is not supplied. Any generic high
quality USB charger can be used.
TURNING ON THE HEADPHONES
Press and hold the MFB
2
until the Status LED
4
flashes solid blue for 1 second and then flashes blue
with an ascending ‘beep’ sound.
The headphones enter pairing mode automatically
when no device is paired.
TURNING OFF THE HEADPHONES
To turn off the ML 100 headphones, press and hold
the MFB
2
for 2 seconds until the Status LED
4
flashes red. There will be a series of descending
tones and the headphone will turn off.
PAIRING TO A DETECTOR
1.
Place the headphones and the detector no more
than 1 metre (3 feet) apart.
2.
Ensure the headphones are turned off.
3.
Press and hold the MFB
2
until a double
ascending tone is heard and the Status LED
4
flashes red and blue.
4.
Press and hold the wireless button on the
detector for 3 seconds. The Bluetooth icon on the
detector display will flash rapidly.
5.
When the pairing is complete, the headphones
will beep and the Status LED
4
will flash blue
3 times repeatedly, indicating that they are
connected to the detector.
NOTE
: If the pairing cannot be completed within
5 minutes after the pairing mode has been
activated, the headphones will automatically enter
Standby Mode.
NOTE
: ML 100 headphones can be paired with two
devices simultaneously so you can pair them with
both your detector and your smart phone.
CONNECT WITH THE LAST PAIRED DEVICE
The headphones will automatically connect with the
last-paired device. If connection is successful, the
Status LED
4
will flash blue 3 times repeatedly.
RESET TO FACTORY DEFAULTS
Make sure the headphones are turned off. Press the
MFB
2
for approximately 10 seconds until there are
2 beeps and the Status LED
4
flashes pink 2 times.
Release the button.
The Status LED
4
will now be flashing red and blue,
indicating that the headphones are in pairing mode.
All previously paired devices will be unpaired.
MUSIC FUNCTIONS
PLAY / PAUSE MUSIC
Press the MFB
2
to pause / play music on your
connected device.
When music is playing, the Status LED
4
will flash
blue 3 times repeatedly.
NEXT / PREVIOUS TRACK
Long press the button
1
for 2 seconds to
play the next track.
Long press the Volume − button
3
for 2 seconds to
play the previous track.
ADJUST THE VOLUME
Press the button
1
once to increase the
volume by one level.
Press the Volume − button
3
once to decrease the
volume by one level.
When maximum or minimum volume has been
reached there will be a high or low tone (beep).
CONNECTING THE AUXILIARY CABLE
The ML 100 headphones are supplied with a
detachable 3.5 mm (
1
/
8
inch) auxiliary cable for wired
operation. This allows the headphones to be used
if the battery is flat, or for use with devices that do
not have Bluetooth capability.
To use the cable, plug the connector into the
headphone jack
6
and turn 90° anti-clockwise to
lock the connector. This prevents the connector
from being accidentally disconnected.
VOLUME PLUS BUTTON (+)
Increases the Volume by one level, plays the next
track (music function).
MULTI-FUNCTION BUTTON (MFB)
Turns the headphones on or off, plays and pauses
music (music function), activates Pairing Mode,
resets the headphones to factory defaults.
VOLUME MINUS BUTTON (−)
Decreases the Volume by one level, plays
previous track (music function).
STATUS LED
Alternating blue / red
Pairing mode
Flash blue 3 times
Connected
Flash blue 2 times
Standby mode
Solid red
Charging
Solid Blue
Charging complete
USB MICRO-B CHARGING SOCKET
HEADPHONE SOCKET 3.5 mm (
1
⁄
8
inch)
1
2
3
4
5
6
1
2
3
4
5
6
