DE-35 projector mount user manual
Product appearance Figure 1-2
Figure 1-1
Main view
Left view
Top view
Length L
(mm)
Width W
(
mm
)
Height H
(
mm
)
(Long + short pole)
(Wall tiles)
(Long Pole)
(Short Pole)
Min
Max
Min
Min
Max
Max
(Extended
long)
(Long tube)
(Short tube)
Product
Type
Figure 1-3
Tube expansion
length
Rated load
(Bearing)
Min
Max
Installation hole distance
(mm)
3 holes LB
4 holes LC
Mounting hole type
Section B
Section E
Section D
Section C
Figure 1-3
.
1
Figure 1-3.2
Figure 1-3.3
Figure 1-3.4
Accessories
left/right adjustable angle
tilt adjustable angle
up/down
adjustable
angle
Mounting Board
Tube
Allen Key
Gloves
Inner-Hexagon
Screws*5
ST6
*
45Automatic
bolts*4
Wall hanging
special
(
No accessories for
non wall hanging)
Plastic pad for hanger
installation*4
Installation Steps
Figure 1-8
Figure 1-4
Figure 1-9
Figure 1-6
Figure 1-7
Figure 1-10
Figure 1-11
Figure 1-5
Step 1: open the package, take out the
upper top plate, and pipe components, screw
out the three screws on the pipe, align the
round pipe with the upper top plate (pay
attention to the direction prompt), and then
screw in the screws for fastening connection.
Refer
fi
gure 1-4
Step 2: take the octopus out of the packing
box, as shown in Figure 1-5, and separate the
components and along the guide groove
by hand. Refer
fi
gure 1-6
Step 3: install the assembly with the
projector. According to the actual size
of the projector (the installation hole
position is different), each group of
connecting arms and movable arms
are fastened, and the distance locking
screw can be adjusted appropriately.
Refer
fi
gure 1-7
Hoisting
Step 4-1: align the assembly with the assembly
in Figure 1-4, and screw in the screw (Refer
fi
gure 1-8 )
Ceiling
Borehole site
Electric drill
expanded colloidal particles
Ceiling
Mounting board
Step 4-2: determine the position of the hanger to be installed on the ceiling,
paste the label of the drilling position, use the drilling tool to align the hole
position, drill four
Φ
10 holes, knock in the expanded rubber particles, and
screw in the st6x45 self tapping screw to install the upper roof assembly
on the ceiling. Refer
fi
gure 1-9 (Suitable for ceiling hoisting and installation)
Step 4-3: put the corresponding wire rod of the projector
through the inner tube, insert the inner tube into the pipe
on the
fi
xed ceiling, lift the octopus (installed for speculation)
with both hands to hang the axial screw along the guide
chute, and lock the left and right four adjusting screws.
Refer
fi
gure 1-10 (suitable for ceiling hoisting and installation)
Step 4-4: debugging the projector: height adjustment: loosen the
adjusting handle screw, adjust the screw up and down by hand, and
then tighten the screw; debugging the projector inclination angle:
fi
rst
loosen the screws on both sides with a hexagon wrench, turn the
octopus assembly by hand to make the projector obtain the required
inclination angle, tighten 1-2 screws to prevent angle deviation, and
then tighten the remaining screws after con
fi
rming the angle.
Refer
fi
gure 1-11
Axial screws
Cables
Adjusting
handle
Ceiling
Outer tube
Adjusting handle
Adjust tilt inner hexagon screws
(
2 sides)
Adjust screws
(horizontal, left,right)
Adjust screws (2 sides)
1
2
3
1
2
1
±5°
±5°
±15°
200+LA
H
45+LA
H
LC
LB
W
L
820+LA
H
1
2
1
245
345
266
426
160
245
345
110
125
18
245
345
173
179
160
20
245
345
266
426
160
245
345
110
125
18
245
345
890
1050
160
LA（mm）
KG
3
5
35
Please read it carefully before use.
Thank you for purchasing DE-35
fi
xed hanger.
Dear users:
DE-35
DE-20
DE-35
DE-35
DE-35
250
350
250
350
250
350
250
350
250
350
250
350
（
）
radius
112
205
（
Diagonal hole
）
285
450
200+LA
H
2
size
Mounting feet
M5x15 screws*4
M4x20 screws* 4
Expanded colloidal
particles*4
2
