background image

Martindale Electric will carry out routine calibration (on a chargeable basis)
if the instrument is returned, carriage paid, to the address on the final page
of this document. Alternatively, a chargeable collection and return service is
available.

4.5 Repair & Service
There are no user serviceable parts in this unit. Return to Martindale
Electric Company Ltd if faulty, unless fuse replacement only is necessary.
Our service department will promptly quote to repair any faults that occur
outside the warranty period.

4.6 Storage Conditions
The MM37 should be kept in warm, dry conditions away from direct
sources of heat or sunlight, with the battery removed and in such a manner
as to preserve the working life of the multimeter. It is strongly advised that
the unit is not kept in a tool box where other tools may damage it.

4.7 Warranty
Faults in manufacture and materials are fully guaranteed for 2 years from
date of invoice and will be rectified by us free of charge, provided the unit
has not been tampered with and is returned to us with its housing
unopened. Damage due to dropping, abuse or misuse is not covered by the
guarantee. Nothing in these instructions reduces your statutory rights.

Martindale Electric Company Limited

Metrohm House, Penfold Trading Estate, Watford, WD24 4YY, UK.

Tel: +44(0)1923 441717 Fax: +44 (0)1923 446900

E-mail: [email protected]

Website: www.martindale-electric.co.uk

© Martindale Electric Company Ltd.

Registered in England No. 3387451. Rev 1. July 2005

MM37

DIGITAL MULTIMETER

MARTINDALE

E L E C T R I C

Trusted by professionals

INSTRUCTIONS

Summary of Contents for MM37







Reviews: