S
Stta
arrtt H
He
erre
e --
H.O.T. MAGNUM & H.O.T. MAGNUM With BIO-Pro System
Quick Setup Guide
1
Parts Check
Canister Prep
A.
Canister
1.
Lift Cover Lock to Open Canister.
2.
Swing Spring Latch downward
and remove Cover.
3.
Remove Internal Flow Diffuser
and Center Exhaust Tube.
4.
Remove Carbon Media
Container.
B.
Carbon Media Container
1.
Remove Cover and Fill with Black Diamond Carbon.
2.
Replace Cover and rinse thoroughly.
3.
Slide Rite-Size Filter Sleeve over Container.
4.
Replace Container over Impeller Module and Bottom Plate.
5.
Replace Exhaust Gasket around Center Exhaust Tube.
6.
Replace Internal Flow Diffuser.
C.
Fill and Seal Canister
1.
Add water until Internal Flow Diffuser is covered.
2.
Install Exhaust Gasket onto Cover.
3.
Wet D-Ring with
Aquarium Water
.
4.
Replace Canister Cover. Raise Cover Lock to
engage Spring Latch. Snap Spring Latch in to
groove. Push Cover Lock down to close and
seal canister.
Placement
DO NOT PLUG IN.
B.
Hang Canister in desired position on the
OUTSIDE
of aquarium. Adjust Hanger to fit
aquarium frame.
C.
Adjust Leveling Clip.
Hanger
Canister
Leveling
Clip
A.
Install Leveling Clip in slots
at the bottom of Canister.
DO NOT PLUG IN.
Intake/Outlet
Assembly
A.
Install Intake and Outlet Tubes. Wet O-Rings on tube ends with aquarium
water. Snap into place by pushing into proper port until Connector Clip
engages and locks. Intake is marked
“IN”
, Outlet
“OUT”
.
NOTE:
Adjust Split Flow Diffuser Diverter.
Hi-Lo Flow
Side-to-Side Flow
NOTE:
Keep water level above
tube “elbow” at all times.
“OUT”
“IN”
Split Flow
Diffuser Diverter
Connector
Clip
Elbow
Intake Tube
Strainer
CAUTION:
To avoid water spills and
leaks, make sure all connections are
secured where indicated.
NOTE:
A slight rattling noise is normal
ONLY DURING STARTUP. If noise persists,
shut off filter and check for dirt or debris
that may be in bottom of Canister.
NOTE:
Drip Loop
(for safety)
Start Up
STOP:
If assembling H.O.T. Magnum with (BIO-Pro
System),
DO NOT PLUG IN.
Continue on to STEP #6
for ADDITIONAL connection directives.
Plug in power cord. Be sure
to create a “Drip Loop”. Press
On/Off switch to start filter.
Parts Check
H.O.T. MAGNUM BIO-Wheel Pro System
Cover
BIO-Wheel
Bearings
BIO-Wheel
Assembly
Connector
Clips
Filter
Housing
Spray
Bar
Sliding Nut
and Screw (L-R)
Hose
Barbed Elbow
Adapter
Barbed Elbow Connector
w/ O-Rings
Spray Bar
O-Rings
Snapper
Clamps
Mount & Placement of Filter Housings
A.
Check BIO-Wheel Assembly for proper installation. BIO-Wheel should rotate
freely. Also check that the Spray Bar is snapped in place with Connector Clip.
C.
Mount the Filter Housing on the
back wall of aquarium, next to H.O.T.
Magnum canister on Outlet Tube side.
Replace Filter Housing Cover.
B.
Thread the screws through the sliding
nuts on the Filter Housing. (Left and right
nuts are marked. If nuts have slipped off
the housing, reinstall.) Tighten screws so
Filter Housing will not slip.
NOTE:
Remove
Paper insert from
each BIO-Wheel
NOTE:
Do not over tighten
Filter Housing Cover
Connector
Clip
Spray
Bar
NOTE:
To remove Spray Bar for cleaning, push
Connector Clip downward (Don’t Squeeze).
Connector
Clip
TO CHANGE FILTER MEDIA...
Shut down system and remove Canister. Carry to sink. Remove Cover.
Change Media. Secure Cover. Return Canister. Restart Filter.
05/07 11957
(800) 322-1266
Questions or Missing Parts?
Call Customer Service at:
www.marineland.com
NOTE:
Drip Loop
(for safety)
Start Up
1
11
16
4
13
4
15
10
4
5
6
7
CAUTION:
To avoid water spills and
leaks, make sure all connections are
secured where indicated.
NOTE:
A slight rattling noise is normal
ONLY DURING STARTUP. If noise persists,
shut off filter and check for dirt or debris
that may be in bottom of Canister.
8
Air Ejector
Cleaning
Wand
Squeeze
to
open Impeller
Module
Silicone
Lubricant
Switch out Carbon Media
Container with Micron Cartridge
and Rigid Core.
Micron Cartridge
Outside
Rigid Core
Inside
For Periodic Water Polishing
or Gravel Washing. . .
Gaskets
Canister Prep
2
b
3
A
1
A
2
A
3
Remove
Internal Flow
Diffuser
B
1
B
2
B
3
Replace
Rite-Size
Filter Sleeve
B
4
Center
Exhaust Tube
B
5
Gaskets
Remove
Center
Exhaust Tub
& Gasket
A
4
Remove
Carbon
Media
Container
A
2
Remove
Cover & Gasket
B
6
Internal
Flow
Diffuser
Cover Lock
Spring Latch
Groove
Connector
Clip
Snapper
Clamps
Connector Assy.
(Factory Assembled)
Barbed Elbow
Adapter
Barbed Elbow Connector
w/ O-Rings
Connector Assy.
(Factory Assembled)
D.
Snap-Lock Barbed Elbow Connector with
O-Rings into BIO-Wheel Pro and slide Barbed
Elbow Adapter into Outlet Adapter.
Outlet
Adapter
C
3 Wet Cover
D-Ring & Replace
C
1
C
4
On/Off Switch
A.
Plug in power cord. Be sure
to create a “Drip Loop”. Press
on/off switch to start filter.
B.
Adjust BIO-Wheel Spray Bar for
consistent rotation of BIO-Wheel.
On/Off Switch
Spray Bar
NOTE:
If assembling H.O.T. Magnum
with the (BIO-Pro System), Install
Outlet Adapter BW Pro Tube.
Cleaning
Brush
Elbow
Outlet Adapter BW Pro
NOTE:
Keep water level above
tube “elbow” at all times.
NOTE:
To remove Tubes Push (don’t squeeze),
Connector Clip downward. DO NOT remove
clip. Slide Intake or Outlet Tubes out of opening
then release Clip.
5
6
7
8
9
14
3
1)
Intake Tube, Strainer & O-Ring
2)
Outlet Tube, Split Flow Diffuser
& O-Ring
3)
Cover, D-Ring Seal &
Connector Clips - 2
4)
Exhaust Gasket - 2
5)
Internal Flow Diffuser
6)
Center Exhaust Tube
7)
Carbon Media Container & Lid
8)
Rite Size “U” Foam Sleeve
9)
Micron Cartridge & Core
10)
Bottom Plate
11)
Impeller Module
12)
Impeller Assembly
13)
Motor, Canister Collar &
Canister Assembly
14)
Spring Latch
15)
Hanger
16)
Leveling Clip
12
2
C
2
Gaskets
Outlet Adapter
O-Rings
Split Flow Diffuser
Connector
Clips
Additional Quick Setup Guide for
MAGNUM 350 BIO-Pro System
ONLY • Additional Quick Setup Guide for
MAGNUM 350 BIO-Pro System
ONLY • Additional Quick Setup Guide for
MAGNUM 350 BIO-Pro System
ONLY
2
a
