background image

OPTIMAAX

®

 Lift Axle System  

Air Controller Module for 

Freightliner Vehicles

SUBJECT: 

Service Instructions

LIT NO:

 17730-310

DATE:

 July 2018 

REVISION:

 A

TABLE OF CONTENTS

Section 1  Introduction

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .2

Section 2  Product Description

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .2

Section 3  Important Safety Notice

   .  .  .  .  .  .  .  .  .  .  .  .4

Section 4  Definitions

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .8

Section 5  Parts List

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .9

Section 6  Air Controller Module

   .  .  .  .  .  .  .  .  .  .  .  . 10

Section 7  Wiring Diagram

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 11

Section 8  Preventive Maintenance

   .  .  .  .  .  .  .  .  .  . 12

Section 9  Air Controller Manifold Diagram

   .  .  . 13

Section 10  Vehicle Air Plumbing Diagram

   .  .  .  . 15

Section 11  System Operation

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 16

Section 12  Diagnostic Tool Software

   .  .  .  .  .  .  .  .  . 17

Section 13  Troubleshooting Guide

   .  .  .  .  .  .  .  .  .  .  . 21

Electronic Components   .  .  .  .  .  .  .  .  .  .  .  .  . 21
Fault Codes  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 23

Summary of Contents for OPTIMAAX

























Reviews: