background image

Page 1 of 20

507389-02

Issue 1733

Save these instructions for future reference

 

(P) 507389-02

*P507389-02*

Manufactured By

Allied Air Enterprises LLC

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

This manual must be left with the homeowner for future reference.

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in 

manuals, be alert to the potential for personal injury or death.

Improper installation, adjustment, alteration, service 

or maintenance can cause property damage, personal 

injury or loss of life. Installation and service must be 

performed by a licensed professional installer (or 

equivalent), service agency or the gas supplier.

 WARNING

For your safety, do not store or use gasoline or other 

flammable vapors and liquids in the vicinity of this or any 

other appliance. Such actions could result in property 

damage, personal injury, or death.

 WARNING

Do not store combustible materials near the furnace or 

warm air ducts. The material may ignite by spontaneous 

combustion creating a fire hazard.

 WARNING

These units are not approved for mobile home 

applications. Such use could result in property damage, 

personal injury, or death.

 WARNING

If  these  instructions  are  not  followed  exactly,  a  fire 

or explosion may result causing property damage, 

personal injury, or loss of life.

 CAUTION

Installation shall be made in accordance with the 

requirements of the local utility and other authorities 

having jurisdiction, or with the National Fuel Gas 

Code, ANSI Z223.1 (latest edition) and the National 

Electrical Code. Any alteration of internal wiring will void 

certification and warranties.

 CAUTION

INSTALLATION INSTRUCTIONS

HWC9 V-Series

TM

 Models

Table of Contents

Installation ...................................................................2

Electrical Connections .................................................8

Start-Up .....................................................................12

Operation ...................................................................13

Maintenance ..............................................................16

Summary of Contents for HWC9 V-Series





















Reviews: