background image

 

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com 

©2015 M2 Antenna Systems Incoporated 

 

11/14/18 

Rev.03 

Model  ......................................... KT34M2 
Frequency Range ....................... 14.0-14.350  MHz 
Frequency Range ....................... 21.0-21.450  MHz 
Frequency Range ....................... 28.0-29.0 MHz 

*

Gain in free space ..................... See  Chart 

Front to back .............................. See Chart 
Feed type ................................... “T” Match 
Feed Impedance. ....................... 50 Ohms Unbalanced

 

Maximum VSWR ........................ 1.5:1 
 

Input Connector .......................... SO-239, Others avl. 
Power Handling .......................... 3 kW, Higher avl. 
Boom Length / Dia ...................... 16’ / 3.0 x .065 Wall 
Element Length / Dia. ................. 25’ / 1” To 1/2” 
Turning Radius: .......................... 15’ 
Stacking Distance ....................... 37’ To 43’ 
Mast Size .................................... 2” to 3 ” Nom. 
Wind area / Survival ................... 4.5 Sq. Ft. / 100 MPH 
Weight / Ship Wt. ........................ 40 Lbs. / 62 Lbs. 
 

M2 Antenna Systems, Inc. 

Model No: KT34M2 

FEATURES: 

 

The  KT34M2 is now the best performing and strongest short tribander available today.  All four elements resonant 

on each band.  A dual driven element allows a beautiful flat match, broad gain, and high front to back curves across 10, 
15, and 20M.  A 3kW 4:1 balun efficiently matches the antenna to 50

.  All sheet metal parts has been upgraded to our 

new machined shorting bars, stiffening and strengthening the antenna noticeably.  The long term performance is en-
hanced by the total contact machined joints. This antenna will be competitive with most monobanders! Be surprised, get 
the NEW KT34M2.    

SPECIFICATIONS: 

10m

 

 

 

f, MHz

 

G, dBi

 

F/B, dB

 

28.0

 

7.3

 

18

 

28.2

 

7.3

 

23

 

28.4

 

7.4

 

25

 

28.6

 

7.5

 

24

 

29.2

 

7.6

 

20

 

15m

 

 

 

f, MHz

 

G, dBi

 

F/B, dB

 

21.0

 

6.9

 

19

 

21.1

 

6.9

 

22

 

21.2

 

7.0

 

24

 

21.3

 

7.0

 

24

 

21.45

 

7.1

 

23

 

20m

 

 

 

f, MHz

 

G, dBi

 

F/B, dB

 

14.0

 

6.5

 

17

 

14.1

 

6.6

 

24

 

14.2

 

6.7

 

21

 

14.35

 

6.8

 

23

 

*Subtract 2.14 from dBi for dBd 

Summary of Contents for KT34M2















Reviews: