Lowrance EP-85R Installation And Operation Instructions Manual Download

Page: 1 / 32

Pub. 988-0154-522

EP-85R Storage Device

Electronic Sensor

Installation and Operation Instructions

This document shows how to connect an EP-85R storage device to a

NMEA 2000

network. The EP-85R stores Fuel Used, Trip Fuel Used

and Seasonal Fuel Used data for up to three NMEA 2000 compatible

engines that output standard NMEA 2000 Fuel Rate Data.
NMEA 2000 is the communication bus standard developed by the

National Marine Electronics Association (NMEA) for use in boats.

Lowrance has introduced a line of products that can communicate over

a NMEA 2000 network (LowranceNet).
All Lowrance NMEA 2000 capable devices are either NMEA 2000

certified or certification is pending.

CAUTION:

Installing LowranceNET NMEA 2000 devices is

significantly

different

from installing earlier Lowrance components without

NMEA 2000 features. You should read all of the installation
instructions before proceeding. Decide where you want to install
all components before drilling any holes in your vessel.

Some sonar or GPS display units may require a software upgrade to

display NMEA 2000 data correctly. For free software upgrades or

additional information on the LowranceNet NMEA 2000

network

system, visit our web site, www.lowrance.com.

The EP-85R Storage Device.

Smart module

Red NMEA 2000
connector

Summary of Contents for EP-85R

































Search results

Summary of Contents for EP-85R

Reviews:

Related manuals for EP-85R

Brands by name

Popular brands

Lowrance EP-85R, Installation And Operation Instructions Manual

Search results

Summary of Contents for EP-85R

Reviews:

Related manuals for EP-85R

Brands by name

Popular brands