Lancaster 7-LX-100 Installation, Operating And Service Manual Download

Page: 1 / 30

PAGE 1

In the event that you need assistance for servicing your water softener, please first contact the

professional contractor who installed the system.

Congratulations on purchasing your new

Lancaster Water Softener

. This unit is designed to give

you many years of trouble free service. When installed in accordance with the following instructions

and if given reasonable care, clear-soft water will be the result. For servicing and future inspection

purposes, please file this booklet with your important documents.

7-LXC-50
7-LXC-75
7-LXC-100
7-LX-75
7-LX-100
7-LX-150
7-LX-200
7-LX-300

ELECTRONIC WATER SOFTENER WITH

THE X-FACTOR CONTROL VALVE

PROGRAMMED FOR PRE-FILL BRINING OPTION

INSTALLATION, OPERATING AND

SERVICE MANUAL



Summary of Contents for 7-LX-100































Search results

Summary of Contents for 7-LX-100

Reviews:

Related manuals for 7-LX-100

Brands by name

Popular brands

Lancaster 7-LX-100, Installation, Operating And Service Manual

Search results

Summary of Contents for 7-LX-100

Reviews:

Related manuals for 7-LX-100

Brands by name

Popular brands