background image

FOR YOUR SAFETY:

 This product must be installed and serviced by a professional service technician, 

qualified in hot water boiler and heater installation and maintenance. Improper installation and/or operation 

could create carbon monoxide gas in flue gases which could cause serious injury, property damage, or 

death. Improper installation and/or operation will void the warranty.

 

WARNING

If the information in this manual is not followed 

exactly, a fire or explosion may result causing 

property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

 

     WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use 

any phone in your building.

•  Immediately call your gas supplier from a 

nearby phone. Follow the gas supplier's 

instructions.

•  If you cannot reach your gas supplier, call the 

fire department.

Installation and service must be performed by

a qualified installer, service agency, or gas supplier.

 

AVERTISSEMENT

Assurez-vous de bien suivres les instructions 

données dans cette notice pour réduire au 

minimum le risque d’incendie ou d’explosion ou 

pour éviter tout dommage matériel, toute blessure 

ou la mort.

Ne pas entreposer ni utiliser d’essence ni d’autres 

vapeurs ou liquides inflammables dans le voisinage 

de cet appareil ou de tout autre appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

•  Ne pas tenter d’allumer d’appareils.

•   Ne touchez à aucun interrupteur. Ne pas vous servir des 

téléphones dansle bâtiment où vous êtes.

•   Appelez immédiatement votre fournisseur de 

gaz depuis un voisin. Suivez les instructions du 

fournisseur.

•   Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le sservice des incendies.

L’installation et l’entretien doivent être assurés par un 

installateur ou un service d’entretien qualifié ou par le 

fournisseur de gaz.

Installation and Operation Instructions for

 

®

 

M

INI

-T

HERM 

JX

H241

1200B

Installation and Operation Instructions 

Document 1478B

Residential

 

Gas-Fired

 

Hydronic Boilers 

Sizes 50-200 MBTU/h

Summary of Contents for MINI-THERM JX





















































Reviews: