background image

Installation, Operation and Service Instructions

H0223500-

FOR YOUR SAFETY: This product must be installed and serviced by a professional service technician,
qualified in pool heater installation and maintenance. Improper installation and/or operation could
create carbon monoxide gas in flue gases which could cause serious injury, property damage, or death.
Improper installation and/or operation will void the warranty.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a nearby phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or gas
supplier.

Installation, Operation
and Service Manual
for the

XL-3 Oil-Fired

Pool Heater

Models DP2000
and DP3000

Summary of Contents for DP2000





















Reviews: