background image

COD. 04056G1KUPNA2 (04056GB) - 18.11.2008

MODEL:  GWS 4711.0 M

Dear Customer,

Thank you for having purchased one of our products.

We are certain that this new, modern, functional and practical appliance, built with the very highest

quality materials, will meet your requirements in the best possible way. This appliance is easy to

use. It is, however, important to thoroughly read the instructions in this handbook in order to obtain

the best results. 

These instructions are only valid for the countries of destination, the identification symbols of

which are indicated on the cover of the instruction manual and on the appliance itself.

The manufacturer shall not be held responsible for any damages to persons or property caused

by incorrect installation or use of the appliance.

The Manufacturer shall not be held responsible for any inaccuracies in this handbook due to printing or

transcription errors; the designs in the figures are purely indicative. The Manufacturer also reserves the right

to make any modifications to the products as may be considered necessary or useful, also in the interests

of the user, without jeopardizing the main functional and safety features of the products themselves.

INSTRUCTIONS AND ADVICE FOR THE 

USE, INSTALLATION AND MAINTENANCE

OF BUILT-IN GLASS HOT PLATES

Summary of Contents for GWS 4711.0 M

















Reviews: