background image

   

                                                                         

1418848-2A-C          

                                                                                                                                          1   

  

   

                                                                          

1418848-2A-C           

                                                                                                                                         8 

  

INSTALLATION INSTRUCTIONS

URBANITY

+

25717T-9    

Recessed Thermostatic Dual Shower Faucet-Multifunction Showerhead

URBANITY

+

SERVICE PARTS

**Color code must be specified when ordering.

BEFORE YOU BEGIN

All information is based on the latest product information available at the time of publication. Kohler Co. reserves the right 

to make changes in product characteristics, packaging, or availability at any time without notice.

Please leave these instructions for the consumer. They contain important information.

OPERATION INSTRUCTIONS

1. Minimum supply pressures: 0.1MPa(1bar).

2. Recommended supply static pressures: 0.3MPa(3bar) on hot and cold water.

3. Supply pressure greater than 0.5MPa(5bar): install a pressure reducer.

4. Hot water temperatures, minimum: 50ºC, maximum: 80ºC.

5. Recommended hot water temperature: 65ºC(energy-saving).

6. Setting range, approximately: 20ºC to 49ºC.

7. Safety stop at: 37ºC.

8. Maximum mixed water temperature: 49ºC.

9. The highest environment temperature for handshower & showerhead is 60ºC. Please keep handshower, showerhead 

and shower arm away from heater, or it may become damaged and cause injury to the user.

OPERATION CONDITION

25717T-9    

Recessed Thermostatic Dual Shower Faucet-Multifunction Showerhead

The temperature is set by slowly turning the temperature handle(right-hand handle). For safety reasons, there is a stop 

that limits temperature to 37ºC. To get a higher temperature, push the button(on right-handle) and continue turning the 

temperature handle counter-clockwise.

Water flow and dispense is set by switch buttons. Press any switch button on the faucet body, the water will run from 

corresponding outlet. Rotate the switch buttons counter-clockwise to reduce flow. 

TOOLS AND MATERIALS (USER SUPPLIED)

Adjustable Wrench             Level                        Drill                           Pencil                     Screwdrivers            Sealant Tape            

Laminar

Katalyst rain

Icon description above switch button 

Handshower

1069458
77420

1410662-CP

(For CY finish)

1348571**

(For other finishes)

1337970**

1081607

1337971**

1061576

1258634**

23096

833438

833730

3008304

1299843**

3008523

870721

834404

1244920

1347562

864922**

1299837

1299846

1176766

1242353

1299857

1242354

834638

1299821

55925

1377201

1423819**

870992

831752

1299825

1259076

3019692

871472

1248781**

42045

1326364

1249005
833730

1242635

1359717

1306343

1306349

833438

833438

1306348**

1092497

1424140-CP

(For CY finish)

1359706**

(For other finishes)

Summary of Contents for URBANITY 25717T-9

Page 1: ...way from heater or it may become damaged and cause injury to the user OPERATION CONDITION 25717T 9 Recessed Thermostatic Dual Shower Faucet Multifunction Showerhead The temperature is set by slowly turning the temperature handle right hand handle For safety reasons there is a stop that limits temperature to 37ºC To get a higher temperature push the button on right handle and continue turning the t...

Page 2: ...apter spline align with the indicator line on the stopper Tighten the screw 52 with a screwdriver Install the temperature handle 49 Ensure the number 37 on temperature handle is upward vertically After assembly it could not be turned counter clockwise if not pushing the button Tighten the screw 50 with 2 5mm hex wrench 27 Insert the plug 51 Clear the Thermostatic Cartridge Very hard water can obst...

Page 3: ... spline 53 Under the normal condition of water flow slowly turn the temperature selector Always in the same direction from the cold water position until water temperature reaches 37ºC If the temperature goes over 37ºC go back to the cold setting and reset it When the temperature is stable do not turn the cartridge spindle Install the adapter spline Ensure the indicator line on the adapter spline a...

Page 4: ... with one waterpipe not provided As figure 6 shown remove the screws 17 from the protector 8 with screwdriver not provided and pull it out Remove the connectors 18 with 8mm hex wrench take off the filter washers 19 Flush water supply pipes for about one minute to remove any debris Insert two G1 2 plugs not provided into the connections 20 Apply water pressure 8bar test on the product Check for lea...

Reviews: