KISAN NEWTON K5, Quick Start Manual

Page: 1 / 2

KISAN: NEWTON K5 (5-POCKET FITNESS SORTER)
BASIC COUNTING MODES FOR PROCESSING MIXED BILLS
MIXED BILL COUNTING
:

PRESS THE MODE KEY UNTIL YOU SEE THE WORD " VALUE " IN THE UPPER LEFT OF THE SCREEN NEXT TO THE FLAG.

TAP THE “ DENOM ” KEY UNTIL YOU SEE THE WORD “ MIX ” IN EACH COUNT WINDOW ON THE SCREEN.

COUNTS ALL MIXED BILLS TO TOP POCKET. IF IT REACHES THE BATCH QUANTITY, IT THEN USES THE SECOND POCKET, AND
SO ON. NUMBERS ON MACHINE SHOW TOTAL NUMBER OF BILLS IN EACH POCKET. THE SCREEN SHOWS TOTAL BILLS IN EACH
POCKET, TOTAL BILLS IN ALL POCKETS, AND TOTAL DOLLAR AMOUNT. TO SEE COUNT BREAKDOWN, TAP “
DATA ” BUTTON ON
SCREEN. TAP “ BACK ” TO EXIT.

IF ANY BILLS ARE REJECTED (BAD, SOILED, COUNTERFEIT), YOU CAN CHECK THE REASON BY TAPPING ON “ REJ ” ON THE
BOTTOM RIGHT OF THE SCREEN (YOU MUST DO SO BEFORE YOU REMOVE THE BILLS)
***NOTE : PRIOR TO RUNNING; MAKE SURE “ FACE " AND/OR " ORIENT " SETTINGS ARE TURNED OFF ***
DIRECTION - FACE/ORIENT ALL-IN-ONE: (IN "MIX" MODE)

PRESS THE MODE KEY UNTIL YOU SEE THE WORD " VALUE " IN THE UPPER LEFT OF THE SCREEN NEXT TO THE FLAG.

TAP THE “ DENOM ” KEY UNTIL YOU SEE THE WORD “ MIX ” IN EACH COUNT WINDOW ON THE SCREEN.

HOLD DOWN THE MODE KEY FOR A COUPLE SECONDS UNTIL THE MODE SCREEN POPS UP

TAP THE BOX WITH THE WORD " DIRECTION " AND IT WILL LIGHT UP

PRESS THE " ACCEPT " BUTTON TO RETURN TO THE MAIN SCREEN

YOU WILL SEE “ DIRECTION ” NEAR THE TOP RIGHT OF THE SCREEN. THIS INDICATES DIRECTION IS TURNED ON

SCANS FIRST BILL AND PUTS ALL BILLS WITH THAT DIRECTION IN THE DESIGNATED POCKET FOR THAT DIRECTION. WHEN IT
SCANS A BILL WITH ANOTHER DIRECTION, IT PUTS ALL BILLS WITH THAT DIRECTION IN THE DESIGNATED POCKET FOR THAT
DIRECTION, AND SO ON. IF ANY POCKET REACHES A BATCH TOTAL, THE MACHINE STOPS AND YOU REMOVE THE BILLS AND
THE MACHINE STARTS UP AGAIN.

REMOVE THE STACKS AND ALIGN ACCORDINGLY. ALL BILLS ARE NOW FACED AND ORIENTED IN ONE PASS-THROUGH.

IF ANY BILLS ARE REJECTED (BAD, SOILED, COUNTERFEIT), YOU CAN CHECK THE REASON BY TAPPING ON “ REJ ” ON THE
BOTTOM RIGHT OF THE SCREEN (YOU MUST DO SO BEFORE YOU REMOVE THE BILLS)
***NOTE : AFTER RUNNING; MAKE SURE TO UNSELECT " DIRECTION " SETTING WHEN FINISHED ***
MIXED BILL SORTING: (BY DENOMINATION)

PRESS THE MODE KEY UNTIL YOU SEE THE WORD " VALUE " IN THE UPPER LEFT OF THE SCREEN NEXT TO THE FLAG.

TAP THE “ DENOM ” KEY UNTIL YOU SEE THE DIFFERENT DENOMINATIONS LISTED IN EACH COUNT WINDOW (USD 1, USD 5,
ETC).

TO CHANGE WHICH DENOMINATION GOES TO WHICH POCKET, HOLD THE “ MODE ” KEY FOR A COUPLE SECONDS UNTIL THE
SCREEN CHANGES. TAP THE POCKET (A, B, C, D) YOU WISH TO CHANGE, THEN TAP THE NUMBER, THEN CHOOSE THE
DENOMINATION YOU WANT IN THAT POCKET. TAP “
BACK ” TO CHOOSE THE NEXT POCKET. WHEN DONE, TAP “ ACCEPT ”. YOU
CAN SET MULTIPLE DENOMINATIONS IN EACH POCKET IF YOU WISH.

BATCHING CAN BE PERFORMED AT THIS TIME FOR STRAPPING BILLS.

TAP THE “ BATCH ” BUTTON ON THE SCREEN TO CYCLE THROUGH THE PRESET BATCH QUANTITIES. THIS SETS THE SAME
QUANTTY FOR EVERY POCKET.

TO SET DIFFERENT QUANTITIES FOR EACH POCKET, HOLD THE “ BATCH ” KEY FOR A COUPLE SECONDS UNTIL THE SCREEN
CHANGES. TAP THE POCKET (A,B,C, D) YOU WISH TO CHANGE, THEN TYPE IN THE QUANTITY YOU WANT IN THAT POCKET.
YOU CAN SET EACH POCKET INDIVIDUALLY. TAP “
ACCEPT ” TO SAVE.

IF ANY BILLS ARE REJECTED (BAD, SOILED, COUNTERFEIT), YOU CAN CHECK THE REASON BY TAPPING ON “ REJ ” ON THE
BOTTOM RIGHT OF THE SCREEN (YOU MUST DO SO BEFORE YOU REMOVE THE BILLS)
***NOTE : PRIOR TO RUNNING; MAKE SURE “ FACE " AND/OR " ORIENT " SETTINGS ARE TURNED OFF ***
FITNESS/ATM MODE

PRESS THE MODE KEY UNTIL YOU SEE THE WORD " FITNESS " IN THE UPPER LEFT OF THE SCREEN NEXT TO THE FLAG.

TAP THE “ DENOM ” KEY UNTIL YOU SEE “ MIX ” IN EACH COUNT WINDOW.

THE DEFAULT SENSITIVITY LEVEL IS 9. TO ADJUST THE SENSITIVITY LEVELS, TAP THE “ MENU ” BUTTON, AND CHOOSE
“ FITNESS LEVEL ” OR “ TAPE LEVEL ”.

IN THE “ FITNESS LEVEL ” SCREEN, THERE ARE 2 ADJUSTMENTS, ON FOR “ FITNESS LEVEL ” AND ONE FOR “ ATM LEVEL ”.
USE THE ARROWS TO RAISE OR LOWER THE LEVEL TO YOUR DESIRED NUMBER. THE LOWER THE NUMBER, THE FEWER
BILLS ARE PROCESSED AS FIT/ATM. THE HIGHER THE NUMBER, THE MORE BILLS ARE PROCESSED AS FIT/ATM. WHEN
DONE, TAP “
ACCEPT ” AND THEN “ BACK ”.

IN THE “ TAPE LEVEL ” SCREEN, USE THE ARROWS TO RAISE OR LOWER THE LEVEL TO YOUR DESIRED NUMBER. THE
HIGHER THE NUMBER, THE MORE SENSITIVE IT IS TO TAPE. THE LOWER THE NUMBER, THE LESS SENSITIVE.WHEN DONE,
TAP “
ACCEPT ” AND THEN “ BACK ”.

YOU CAN CHANGE WHICH TYPE OF BILLS ( ATM, FIT, UNFIT ) GO IN TO WHICH POCKET. HOLD THE “ MODE ” KEY FOR A
COUPLE SECONDS UNTIL THE SCREEN CHANGES. TAP WHICH POCKET YOU WANT TO CHANGE ( A, B, C, D ), THEN TAP THE
BOX NEXT TO FITNESS. CHOOSE WHICH TYPE OF BILLS YOU WANT IN THE POCKET ( ATM, FIT, UNFIT ). YOU CAN CHOOSE
MULTIPLE TYPES PER POCKET IF YOU WISH, BUT USUALLY IT IS EASIER TO DO ONE TYPE PER POCKET. WHEN DONE, TAP
“
BACK ”, AND THEN “ ACCEPT ”.

IF ANY BILLS ARE REJECTED (BAD, SOILED, COUNTERFEIT), YOU CAN CHECK THE REASON BY TAPPING ON “ REJ ” ON THE
BOTTOM RIGHT OF THE SCREEN (YOU MUST DO SO BEFORE YOU REMOVE THE BILLS)