background image

FUN-50 

ARF 

ASSEMBLY MANUAL 

 
 
 

 

 
 
 

This Manuel is the sole property of Kangke Industrial USA, Inc. Reproducing any part without the 

consent of Kangke Industrial USA, Inc. is a lawful violation. 

 

Kangke Industrial USA, Inc.  65 East Jefryn Blvd.  Deer Park NY 11729 

http://www.kangkeusa.com

     E-mail: 

[email protected]

 

1-877-203-2377                           fax 1-631-274-3296 

 

Warranty: 

Kangke Industrial USA Inc. guarantees the kit to be free of defects in both material and workmanship at the date of 

purchase. This warranty does not cover any parts damaged by use or modifications. In no case shall Kangke Industrial’s liability exceed the 
purchase cost of this kit. Since Kangke Industrial has no control of final assembly and material used by user for final assembly, no liability 
shall be assumed or accepted for any damage resulting from the use by user of final user-assembled products. This kit has been flight test for 
normal use. If the plane will be used for extremely high stress flying, the modeler is responsible for reinforcing the high stress points. Inspect 
this kit immediately after receiving it, report any missing and damaged parts within 10 business days otherwise the claim may be denied. 

Summary of Contents for FUN-50













Reviews: