K-EDGE BRAZE-ON CLAMP ADAPTER (SOLD SEPERATELY - K13-030-34.9)
K-EDGE BRAZE-ON ADAPTER
"BACK-BOLT"
1x M5 x 12mm FHCS
"NON-DRIVE / INSIDE" CAGE HALF
"LOCKING-BOLTS"
2x M4 x 12mm SHCS
"DRIVESIDE / OUTSIDE" CAGE HALF
"CAGE-BOLTS"
3x M2.5 x 12mm SHCS
K13-050 - K-EDGE CX SINGLE-RING GUIDE W/ O.L.S.- TECHNICAL INSTRUCTIONS
DESCRIPTION OF PARTS
OR
0.45 N-m (+/- 0.09 N-m)
EQUALLY TORQUE
TO 2.00 N-m (+/- 0.20 N-m)
4.00 N-m (+/- 0.50 N-m)
+5°
-5°
A
A
DESCRIPTION OF O.L.S. - 'OPPOSING-LOCK-SYSTEM'
OPENING FOR 3mm HEX
TOOL ACCESSIBILITY
B
SECTION A-A
VIEW OF MECHANISM
DETAIL B
OF MECHANISM
"BACK-BOLT"
SETS
HORIZONTAL DISTANCE FOR
CHAINLINE ALIGNMENT
"LOCKING-BOLTS"
PRODUCE AN
'OPPOSING'
FORCE ONTO THE BACK-BOLT
-
LOCKING
THE CAGE INTO DESIRED
POSITION
K-EDGE BRAZE-ON CLAMP ADAPTER
M5 FLAT WASHER
M5 x
20mm
SHCS
IF YOUR FRAME
DOES NOT
HAVE A BRAZE-ON,
USE SETUP BELOW
K-EDGE RADIUS WASHER
M5 FLAT WASHER
M5 x
20mm
SHCS
MOUNTING OPTIONS
IF YOUR FRAME
DOES
HAVE A BRAZE-ON,
USE SETUP BELOW
K-EDGE BRAZE-ON
ADAPTER
BACK-BOLT
APPLY BLUE
LOCTITE ON
THREADS
d
(BOTTOM VIEW)
d
K-EDGE BRAZE-ON
ADAPTER
INNER CAGE
LOCKING-BOLTS
*APPLY BLUE LOCTITE*
**
LIGHTLY TIGHTEN
**
(a)
DETAIL (a)
**
ATTENTION
**
ENSURE
NO
CONTACT
BETWEEN THE
ADAPTER AND FRAME
(b)
DETAIL (b)
**
ATTENTION
**
ENSURE
NO
CONTACT
BETWEEN THE
ADAPTER AND FRAME
BRAZE-ON RECOMMENDATIONS:
38T - 42T > UPPER MOUNTING HOLE
•
42T - 46T > LOWER MOUNTING HOLE
•
UPPER
MOUNTING HOLE
LOWER
MOUNTING HOLE
2.1
DETAIL 2.1
SCALE 1 : 2
ANGLE CAGE TO NEUTRAL
(0-DEGREE) POSITION
1
SET "BACK-BOLT" DISTANCE
MOUNT TO BE USED:
K-EDGE BRAZE-ON CLAMP ADAPTER -
d = 2.9mm
•
BRAZE-ON ON FRAME -
d = 4.9mm
•
2
INSTALL NON-DRIVE CAGE
AND SET INITIAL ANGLE
INSTALLATION STEPS: 1 > 2 > 3
(a)
OR
(b)
>
OPTION (a)
INCLUDED
OPTION (b)
SOLD SEPERATELY
3(a)
3(b)
INSTALL ONTO FRAME PER
YOUR
"MOUNTING OPTION"
(TRUE BRAZE-ON SHOWN)
INSTALL ONTO FRAME PER
YOUR
"MOUNTING OPTION"
(CLAMP ADAPTER SHOWN)
OR
PROCEED TO NEXT PAGE FOR
SETUP AND ADJUSTMENT
NOTE:
K-EDGE BRAZE-ON ADAPTER
M5 MOUNTING HOLES
THE K-EDGE BRAZE-ON
ADAPTER HAS 2x M5 MOUNTING
HOLES AVAILABLE FOR
VARIABLE CHAIN RING SIZES.
DEPENDING ON YOUR
CONFIGURATION, YOU MAY
NEED TO USE EITHER THE
UPPER OR LOWER MOUNTING
HOLE.
CLAMP RECOMMENDATIONS:
ALL SIZES USE LOWER MOUNTING HOLE
•
DEPENDENT ON FRAME DESIGNS
•
REQUIRED TOOLS:
2mm HEX KEY ('L' OR 'T' SHAPE)
•
3mm HEX KEY ('L' OR 'T' SHAPE)
•
4mm HEX KEY ('L' OR 'T' SHAPE)
•
**IF THERE
IS
FRAME CONTACT, CONTACT K-EDGE IMMEDIATELY**
**IF THERE
IS
FRAME CONTACT, CONTACT K-EDGE IMMEDIATELY**
THE ABOVE DISTANCES ARE RECOMMENDATIONS TO SAVE YOU
TIME DURING THE ADJUSTMENT STEPS. IF THESE DISTANCES
ARE NOT CORRECT, PLEASE MAKE NOTE AND NOTIFY K-EDGE.
