background image

 WARNING

FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and 

qualified in pool equipment by the jurisdiction in which the product will be installed where such state or 

local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment 

installation and maintenance so that all of the instructions in this manual can be followed exactly. Before 

installing this product, read and follow all warning notices and instructions that accompany this product. 

Failure to follow warning notices and instructions may result in property damage, personal injury, or death. 

Improper installation and/or operation may void the warranty.

Improper installation and/or operation can create unwanted electrical hazard which can 

cause serious injury, property damage, or death. 

ATTENTION INSTALLER - This manual contains important information about the installation, 

operation and safe use of this product. This information should be given to the owner/

operator of this equipment.

INSTALLATION AND 

OPERATION MANUAL

 

JCP Series High Performance 

Commercial Pumps

JCP05-1CT-S

JCP07-1BD-S

JCP05-3AT-S

JCP07-3AT-S

JCP10-3AT-S

JCP15-3AT-S

JCP05-1CT-N

JCP07-1BD-N

JCP05-3AT-N

JCP07-3AT-N

JCP10-3AT-N

JCP15-3AT-N

H0679300_REV C

ENGLISH  |  FRANÇAIS  |  ESPAÑOL

Summary of Contents for JCP Series













































































































Reviews: