background image

Installation Data

Installation Man u al

PDA - Pool Digital 
Assistant

 WARNING

FOR YOUR SAFETY - This product must be installed and serviced by a pro fes sion al pool/spa service 
technician. The procedures in this manual must be followed ex act ly.   Failure to follow warning notices 
and instructions may result in property damage, serious injury, or death.

Pool/Spa Combination Systems and 
Pool Only/Spa Only Systems
(Models PS4, PS6, PS8, P4, and P8)

Firmware Revision 2.6

H0572200B

ATTENTION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications.  However, 
there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment to an electrical source on a circuit different from that to which the receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

Modifi cations made to this equipment, which are not authorized by the manufacturer, may void the user’s authority 
to operate this equipment.

Summary of Contents for and P8

































Reviews: