Thank you for purchasing an INTEGRAL LED product. When installed correctly this unit will provide years of
service. For support or warranty information please see integral-led.com.
Important Details – Please read prior to installation
1. Installation must be completed by a qualified electrician in accordance with all recognised local and national electrical and
construction regulations.
2. Ensure that the power is OFF during installation and that power cannot be unexpectedly reconnected.
3. The light fitting is designed to operate with a 100V-240V 50Hz/60Hz electricity supply. Do not use the light fitting if damaged
or if the LED protective cover is missing or damaged. Do NOT open the driver over on the rear of the unit or remove the
front protective Cover. There are no serviceable parts inside.
4. This light fitting is rated IP65 (see Technical Features table) – suitable for indoor and outdoor use, on industrial and
commercial applications, e.g. entrances, garages, parking areas, corridors etc.
5. Do NOT cover the light source or heat-sink.
6. To avoid damage; do NOT lift, carry or let the light fitting hang by its cable.
7. Suitable to be mounted on solid flat surfaces and lighting masts. U-shape bracket supplied as standard; other mounting
options available can be found in our website or with your supplier.
8. Failure to comply with the recommendations and instructions provided herein may cause damage to the light fitting
or present a risk of injury or death (e.g. short-circuit, fire, burns or electric shock). Any modifications to the light fitting,
incorrect installation or unsuitable positioning may be dangerous to users and may cause the warranty to become void.
9. Figure images are for illustrative purposes only. Please note the size of the luminaire differs depending on product wattage.
Installation Instructions
10. Ensure that the power is OFF during installation and that power cannot be unexpectedly reconnected.
11. Fix the bracket / Pole Mounting on its definite position, regarding the fixing points dimensions indicated on figure 1.
Fixing accessories are not supplied. Please consider the specific environment characteristics where you are installing the
floodlight to select the adequate fixing devices (salty, humidity, causticity, acidity, temperature)
12. Please consider the structure you are fixing the product to and ensure it can bear the weight of the floodlight before
installation, keeping in mind the effects of wind resistance.
13. Once the bracket is fixed, aim the LED floodlight ensuring the appropriate angle so the area you wish to illuminate is
properly covered (fig 2). Ensure bolts are tight on both sides of the bracket after aiming the product adequately.
14. If needed, a glare shield is available as an accessory. Please, check our website for product details.
15. All floodlights are supplied with 2 meters cable H05RN-F 3x1.00mm2 (fig 3) to connect the floodlight to mains.
16. Use of a suitable junction box or connector providing installed IP65 rating (or greater) is required to connect the floodlight
cable to the mains. Please pay special attention to the cable polarity and earth.
17. Connect the floodlight to the controller using the supplied 2m signal cable with male-female connectors (fig 3). Extension
signal cables are available; please, check our website for product details.
18. The floodlight is a CLASS I device – an EARTH connection is MANDATORY.
19. Check connections and switch power ON when safe to do so.
Product Code
Wattage
Beam Angle
ILFLRGBW001
80W
30°
ILFLRGBW002
60°
ILFLRGBW003
90°
ILFLRGBW004
120°
ILFLRGBW005
85°x135°
ILFLRGBW006
60°x135°
ILFLRGBW011
100W
30°
ILFLRGBW012
60°
ILFLRGBW013
90°
ILFLRGBW014
120°
ILFLRGBW015
85°x135°
ILFLRGBW016
60°x135°
Product Code
Wattage
Beam Angle
ILFLRGBW021
120W
30°
ILFLRGBW022
60°
ILFLRGBW023
90°
ILFLRGBW024
120°
ILFLRGBW025
85°x135°
ILFLRGBW026
60°x135°
ILFLRGBW031
300W
30°
ILFLRGBW032
60°
ILFLRGBW033
90°
ILFLRGBW034
120°
ILFLRGBW035
85°x135°
ILFLRGBW036
60°x135°
INSTALLATION INSTRUCTION
Precision Pro RGBW Floodlight
The floodlights in this range are RED GREEN BLUE and WHITE colour changing
Method to change colour is via a supplied DMX controller
EN
