Always charge the battery at temperatures between 0°
and 45°C (32°F - 113°F).
It is important to perform the full battery charge before
using i7810 for the first time – charge the battery without
interruptions until i7810 terminal indicates the end of
charging process (no moving bars on the battery status
icon).
To prolong battery life:
-
Avoid frequent full discharges. Shallow (partial)
discharges and often charges are preferred. Full
discharge and charge is recommended after every 30-
40 short charge/discharge cycles.
-
Protect batteries from high temperatures (for example,
avoid leaving them in a vehicle on a hot summer day).
To charge the battery:
Place i7810 on the base (the base must be powered up).
Do not place battery on the base by itself, the battery
must be charged while installed in i7810.
Ensure that i7810 is seated securely on the base.
Use the power adapter supplied with i7810. Many
adapters can appear similar and will plug into the base
but will not work properly causing erratic behavior, poor
charging or even damage to the unit.
The i7810 with a fully charged battery can perform up to
200 transactions (
depending of the ticket size,
transaction duration, time between transactions and
backlight usage
).
The battery status is updated on the i7810 display (the
indicator depends of the application):
1 bar represents 25 % of full capacity,
2 bars represent 50 % of full capacity,
3 bars represent 75 % of full capacity,
4 bars represent full capacity.
Moving bars indicate that the battery is being charged.
-
Do not short-circuit batteries.
-
Do not open or alter batteries’ outside structure.
-
Do not expose battery to fire, do not heat it.
-
Do not expose battery to liquid, do not freeze it.
Store batteries at 40% charge level in a cool and dry area.
The recommended storage temperature is 15°C (59°F).
Re-charge them to 40% every 4 months.
3.5.
Connections:
Turn the terminal off before connecting peripherals.
•
Connections on the i7810 hand-held:
Connect LinkBox or ComBox to the RS-232 port, the letters
“TOP” on a connector must be facing up. The green light
(LinkBox only) indicates modem is ready. The light becomes
red while dial connection is used.
LinkBox provides dial connection (asynchronous and
synchronous, V22bis or V34) and powered RS-232 port.
ComBox provides two RS-232 ports, one of them powered
(port marked
RS232-2
).
•
Connections on the base:
Plug the power adapter radial jack into the base port marked
. The green light on the front right hand side of the
base indicates the power is on.
Attach the cable securing plate and fix it with a screw.
4.
Normal Operation:
Depending of the application installed in the terminal, i7810
displays icons indicating:
•
Battery charge level.
•
Charging status.
•
Received signal strength.
Depending of the application, i7810 goes into stand-by mode
after a period of inactivity (in order to prolong battery life).
i7810 can be powered up by pressing the green <
ENTER
>
key.
5.
Technical specifications:
The i7810 communication is based on 802.11b standard,
protected by 128-WEP or WPA security.
Type...........................20 dBm hopping frequency
Bandwidth .................ISM 2.45 GHz
Emitting power ..........
≤
100mW (20dBm)
Range.........................
≈
200 meters or 650 feet (open range)
The power supply
:
•
INPUT .................... AC 120V 60Hz
•
OUTPUT ..... DC 18V 0.9A 16.2VA
6.
Cleaning procedure:
•
The i7810 must be off for all cleaning operations.
•
Do not clean the i7810 with water but with a dry or only
slightly damp cloth.
•
Do not use solvent, detergent or abrasive products.
If the terminal has battery charge problem, clean the contacts
on the battery and on the terminal with a damp cloth.
Do not scratch or scrape the surface of the contacts.
•
If the print quality deteriorates, clean the print head to
remove accumulated paper dust. The print head must be
cleaned with the terminal powered off, using ethanol
applied on a lint-free cloth.
Be aware of the sharp paper cutter and hot printer parts.
Ensure that the ethanol has completely evaporated before
switching the terminal back on.
7.
Customer support and return materials
authorizations contact:
24-Hour North American Customer Support:
Tel: 888.900.8221
Fax: 905.795.9343
Customer Service Centers:
In Canada:
In the USA:
6520 Gottardo Court
6195 Shiloh Road, Suite D
Mississauga, Ontario, L5T 2A2
Alpharetta, GA 30005
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
. Consult the dealer or an experienced radio/TV technician for help.
Ingenico is not responsible for any radio or TV interference caused by unauthorized modifications
to this equipment. Such modifications could void the user’s authority to operate the equipment.
RF Exposure Warning
:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This device must be operated with minimum 20 cm spacing between the antennas and
all person’s body (excluding extremities of hands, wrist and feet) during wireless mode of
operation. Further, this transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
This device and its antenna must not be co-located or operating with any other antenna or
transmitter except Grant condition. Users are not permitted to modify this transmitter device. Any
unauthorized change made to this device could void your authority to operate this device.
Ingenico Inc.
6195 Shiloh Road, Suite D, Alpharetta, GA 30005
Tel: 678.456.1200 Fax: 678.456.1201
www.ingenico-us.com
Ingenico Canada Ltd.
79 Torbarrie Road, Toronto, Ontario, Canada, M3L 1G5
Tel: 416.245.6700 Fax: 416.245.6701
www.ingenico.ca
i7810
Installation Guide
DIV450011A
RS-2332
port
