background image

580 Eastview Drive  |  Laurel, MS 39443

(p) 601.422.0033  |  (f) 601.422.1652  |  Toll-Free: 800.956.3456

www.Howard-Lighting.com

Revised 3/6/2016

Need help? 

Call 1-800.956.3456 to speak with our installation and product experts.

LED W

ork

 L

ight

 i

nstaLLation

 i

nstructions

LWL-TP-44-120 (

WiTh

T

riPod

)

SAFETY PRECAUTIONS

•  Do not open the work light body; no user serviceable parts inside.
•  Do not look directly at lighted fixture. Do not remain in bright light if skin feels 

warm as you are too close to the fixture.

•  Keep fixture away from children.
•  Never use around heavy volatile fluids such as gasoline.
•   Never operate the fixture with missing glass safety shield.
•  This fixture is not intended for use nor safe to use in potentially dangerous locations 

such as places with explosive or flammable atmospheres.

•  Do not handle this fixture when standing on wet or damp surfaces or in water. To 

reduce the risk of electrical shock, this light should always be plugged into properly 

grounded 3-wire outlet. If used while exposed to wet or damp surfaces a ground 

fault outlet (GFCI) should always be used. Do not remove the ground wire or 

grounded plug from the fixture. Always use a U.L. listed 3 wire grounded cord with 

electrical capacity to properly handle this light and other tools you might be using. 

Never use light around swimming pool, hot tubs or saunas.

•  Use only with an extension cord for outdoor use, cord type:

SW,SW-A,SOW,SOW-A,STW,STW-A,STOW,STOW-A,SJW-A,SJOW,SJOW-

A,SJTW,SJTW-A, or SJTOW,SJTOW-A

•  When an extension cord is used with this luminaire, the maximimum cord length 

shall not exceed 50 feet (15.2 m) from where the cord exits the luminaire to the 

receptacle.

assEMBLY instructions

1.  Carefully remove the fixture and all the parts from the box. Set out the tripod legs 

and loosen the black adjustment knob. Slide center pole through adjustment sleeve 

and into bottom pole receiver. Tighten receiver bolt so pole receiver is secure to 

pole. Tighten adjustment knob so legs stay fixed in place. If the floor is not flat, 

the tripod can be adjusted by loosening the nut on the extension leg. Now you are 

ready to install top portion of fixture. (See Figure 1)

2.  Adjust the angle of Yoke by T-Knob on sides of work light heads. Position so yoke 

is in upright position. Center hole in yoke over hole in crossbar. From underside of 

crossbar slide black bolt through hole in yoke. Tighten black knob to secure yoke to 

crossbar. Repeat process for second worklight (See Figure 2).

3.  Line up hole in center of crossbar over tripod “T” (See figure 3). Screw into top of 

pole until snug. Tighten, but do not over tighten.

4.  Lamp height can be adjusted by loosening the compression nut, sliding pole to 

desired height and retightening the nut (See Figure 4).

1

2

3

4

PARTS LIST

• (1) TP Tripod Assembly
• (2) LWL-22-120 Work Light
• (1) Work Light Stand
• (1) Parts Bag

• (2) 1.25”L ¼-20 Carriage Bolts
• (2) ¼” Flat Washers
• (2) ¼-20 Knobs
• (1) ¼-20 Knob Screw

REqUIREd TOOLS

• Adjustable Wrench

Reviews: