background image

II. DETAILED TRACK ASSEMBLY

a.

 Your race set makes two different layouts. Refer to the  Assembly Map for 

detailed track assembly. Start with   the 
Terminal Track 

and continue adding track 

pieces  until your layout is complete.

b.

 Once your layout is assembled,  you’ll need to 

add guardrails. Refer to the Assembly Map for 
placement. To attach a guardrail: gently flex the 
guardrail before attaching it. Carefully attach 
the bottom of the  guardrail first. Then pull up 
and snap into place. Don’t force 
guardrails into place.

1.

  There are letters molded into each 

track piece. These letters are used 
in these instructions to indicate 
which track piece goes where. 
Following the layout drawings on 
the Assembly Map, you may want 
to lay out your track – without 
connecting any track pieces. That 
way you’ll be able to see how the 
track layout goes together.

2.

  To connect track pieces: working on the flat surface, push the ends of the track 

pieces together. Make sure they snap together securely – you’ll hear a click 
when they’re properly connected.

3.

  To disconnect track pieces, 

simply reach underneath where the 
track pieces meet and press the locking 
tabs together with  thumb 
and forefinger as shown.

Follow the step-by-step instructions to set up your race set.

Please separate the “Assembly Map” page, and keep it handy during 
assembly. This page contains the contents list and large-scale Layout 
Drawings of the fully-assembled track. You’ll need to refer to it as you go.

The Assembly Map looks like this:

M0676-0921

© 2008 Mattel, Inc. All Rights Reserved.

SPEED RACER MOVIE: © Warner Bros. Entertainment Inc. 

SPEED RACER: ™ Speed Racer Enterprises, Inc.

(s08)

MAIN LAYOUT DRAWING

ALTERNATE LAYOUT DRAWING

Refer to the package
for color photographs

of the assembled layouts.

This page shows the contents list and large-scale Layout

Drawings of the fully-assembled track (tracks are not drawn to scale).

You'll need to refer to it as you assemble your race set.

Refer to the Instruction Sheet for detailed step-by-step instructions

for setting up and using your race set.

8

GUARDRAILS

6

F

9" RADIUS CURVE

1

C

6" STRAIGHT

1

A

9" TERMINAL TRACK

1

VEHICLE

1

VEHICLE

1

SANDPAPER

1

S

15" SQUEEZE 

2

CONTROLLERS

1

2
3

1

BATTERY PACK

6

CLIPS

1

 = GUARDRAILS

 = TRACK SUPPORTS

1 = Beginner
2 = Average player
3 = Skilled player

1

2

3

1

CARD BOARD

2

 #2 SUPPORTS

1

Use either a diorama or a guardrail on the outside of the curves.

F

F

F

F

S

C

A

1

1

F

F

C

S

F

F

F

F

A

1

2

1

2

3

1

2

3

  

Be sure to check out the Troubleshooting Guide on the back of the 
Assembly Map.

 

I. BASIC TRACK ASSEMBLY

Start out on a clean, hard, flat racing surface – not  carpeting. Take out 
all the track pieces (and other parts) and check them carefully against 
the contents list on the Assembly Map.

 

Sometimes brand-new track may need a quick cleaning for best 

 performance. Check the Maintenance section of this manual for more    

           information.

  

Look for this symbol 

 

throughout this manual. It indicates important 

information.

START HERE! 

Occasionally the metal track rails will stick up too far from the surface 
of a track piece, as shown. This may interfere with vehicle movement. 
To correct, simply press the rail back down with your finger. If the 
problem persists, please contact Customer Service toll-free at 1-888-
557-8926 (see hours of operation in the Warranty section).

Remember: if the track connections aren’t right, electric power won’t 
flow from one track section to the next.

ADULT ASSEMBLY REQUIRED.

CAUTION:  

This product contains a 

sharp edge(s).  For adult assembly 
only.  Take extra care during 
unpacking and assembly.

M0676-0920

5+

INSTRUCTION MANUAL

Keep these instructions 

for future reference, as they contain important information. 

®

Reviews: