background image

Harman®  •  

 Owner s  anual R2   •  200  -

  •  08 1

1

3 -9 0 -0 0 6 8 4 c

Model(s):

XXV Freestanding Pellet Stove

INSTALLER :  Leave this manual with party responsible for use and operation.

OW NER :  R etain this manual for future reference.

Contact your local dealer with q uestions on installation, operation or service.

NOTICE: SAVE THESE INSTRUCTIONS

Please read this entire manual before 

installation and use of this pellet fuel-

burning room heater.  

F ailure to follow these instructions could 

result in property damage, bodily inj ury 

or even death.

•  o not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

•  o not overfire - If any external part starts to glow, you 

are overfiring. Reduce feed rate.  Overfiring will void 

your warranty.

•  Comply with all minimum clearances to combustibles 

as specified.  ailure to comply may cause house fire.

Check building codes prior to installation.
•  Installation  UST comply with local, regional, state and 

national codes and regulations.

•  Contact local building or fire officials about restrictions 

and installation inspection requirements in your area.

CAUTION

Tested and approved for wood pellets and shelled field 

corn fuel only.  Burning of any other type of fuel voids 

your warranty.

CAUTION

Hot glass will cause burns.

• 

o not touch glass until it is cooled

•  NE ER allow children to touch glass
• 

eep children away

•  CARE ULLY SUPER ISE children in same room as 

stove.

•  Alert children and adults to hazards of high temperatures.

  High temperatures may ignite clothing or other 

amma e mater a

• 

eep clothing, furniture, draperies and other flammable 

materials away.

HOT SUR F ACES!

Glass and other surfaces are hot 

during operation AN  cool down.

To  obtain  a  rench  translation  of  this  manual,  please 

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction fran aise de ce manuel, s il 

vous  pla t  contacter  votre  revendeur  ou  visitez  www.

harmanstoves.com

NOTE

 W AR NING

 W AR NING

Owner’ s Manual

Care and Operation

Summary of Contents for XXV




































Reviews: