Harman Super-Magnum Owner'S Manual Download

Page: 1 / 40

3-90-02702R6_03/13

www.harmanstoves.com

Owner's Manual

Installation and Operation

Model:

Super-Magnum

Coal Stoker Stove

NOTICE

•

Important operating and

maintenance instructions

included.

•

Read, understand and

follow these instructions

for safe installation and

operation.

•

Leave this manual with

party responsible for use

and operation.

Please read this entire manual

before installation and use of this

coal-burning room heater.

Failure to follow these instructions

could result in property damage,

bodily injury or even death.

•

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

• Do not overfire - If any external part starts to glow,

you are overfiring. Reduce feed rate. Overfiring

will void your warranty.

• Comply with all minimum clearances to

combustibles as specified. Failure to comply

may cause a house fire.

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult local building, fire officials or authorities having

jurisdiction about restrictions, installation inspection, and

permits.

Hot, will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

fireplace.

• Alert children and adults to hazards of high

temperatures.

High temperatures may ignite clothing or other

flammable materials.

• Keep clothing, furniture, draperies and other

flammable materials away.

HOT SURFACES!

Glass and other surfaces

are hot during operation

AND cool down.

CAUTION

Tested and approved for use with anthracite "rice"

coal only. Burning any other type of fuel will void

your warranty.

DO NOT DISCARD THIS MANUAL

CAUTION

Do Not

Discard

WARNING

Summary of Contents for Super-Magnum









































Search results

Summary of Contents for Super-Magnum

Reviews:

Related manuals for Super-Magnum

Brands by name

Popular brands

Harman Super-Magnum, Owner'S Manual

Search results

Summary of Contents for Super-Magnum

Reviews:

Related manuals for Super-Magnum

Brands by name

Popular brands