PLL ALARM CLOCK RADIO With USB PORT AND SD CARD SLOT
For MP3 FILES PLAYBACK
Model : HX-113CR
INSTRUCTION MANUAL
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Basic Control
Remote Control
1
button
2
SET button
3
MEM/REP button
4
PWR/FUN button
5
C/F / SNZ button
6
EQ/ALM button
7
VOL+ button
8
VOL− button
9
button
10
button
Specifications
FM frequency range
88 – 108 MHz
Supported storage
USB/SD/MMC
Lithium-ion battery
3.7V / 1100 mA
Adaptor input power
DC 5V / 1800mA
Nominal voltage (clock)
3V (1.5V x 2 batteries AG13)
Specifications and functions are subject to change without notice. It is connected with continual improvement of the device.
POWER SUPPLY
Battery Power
• The built-in battery used for the unit power supply is rechargeable. The battery must be fully charged before the first
use. The first charging time should be about 14-16 hours.
• Connect the adapter to a power supply socket, and insert the charging plug into the Power input of the unit.
• The unit will start charging after well connected. When fully charged, the course of charging stops automatically.
Now the adaptor can be unplugged from the unit.
• To ensure safety, neither change the parts and fitments of the battery by yourself nor unwrap the battery. We
suggest you use only the battery and the adapter supplied with the unit, so as not to do the damage to the unit.
Additional power
• Included are 2 AG13 batteries (1.5 V) which are to be inserted in the terminal inside the battery compartment. This
is additional power is intended for operation of clock, alarm, calendar, thermometer and countdown timer. Without
the additional power the time and alarm settings will not be stored if the unit is switched off.
• To install the batteries, unscrew the screw on the battery compartment on the back panel. Make sure to observe
the polarity of the batteries
GENERAL OPERATION
Power on/off
When the unit is connected to the current supply mains, slide the POWER switch to ON
position to switch the power on. To switch the power off, slide the POWER switch to
OFF position.
Clock and calendar
• In clock mode (no ALARM indication) press the SET button to enable
time setting mode. Press repeatedly the
SET
button to go to setting of
parameters in the following sequence:
12/24 hour hour minute year month date.
• Press the
TUNE/
button to adjust the parameter up. Press the
/TUNE
button to adjust the parameter down.
• Day of week will be set automatically.
• In time setting mode, if no button is pressed within 10 seconds after a
parameter is selected, the unit will automatically go to clock mode.
Thermometer
The unit is equipped with a built-in thermometer. The current temperature is
updated every 30 seconds and is shown on the display. In clock mode
press
SNOOZE
button to select Celsius or Fahrenheit thermometer mode.
Backlight
Hold
the
SET
button for
2 seconds
to switch on the backlight, repeatedly
press for 2 seconds to switch it off.
1
TUNE/
button
10
SNOOZE/SLEEP
button
2
SD/MMC memory
card slot
11
MEM/REP button
3
/MEM-UP
button
12
ALARM/EQ
button
4
/TUNE button
13
SET/LIGHT button
5
USB port
14
Telescopic
FM-antenna
6
FUNCTION/
POWER button
15
Battery
compartment
7
VOL− button
16
POWER
ON/OFF
switch
8
VOL+ button
17
Power
(DC5V)
input
9
STOP/MEM-DN
button
18
AUX INPUT
Page 1
Page 2
