Halma BEA ACTIV8 THREE ON User Manual Download

Page: 1 / 8

1/8

ACTIV8 THREE ON

USER’S GUIDE

COMBINED RADAR OPENING AND ACTIVE INFRARED SAFETY SENSOR FOR ESCAPE ROUTE DOORS

Radar Antenna

Cover

Push-Buttons

Radar motion sensor

Radar Antenna clip

Radar tilt angle indication

15°
30°
45°

IR-Presence sensor

IR-Prism

Main Connector

IR curtain adjustment screw

LED turns on

LED flashing slowly LED flashing quickly

Motion detection

Presence detection

Tip

LED display during normal function

GREEN LED

Motion detection

RED LED

Presence detection
Short flash after a motion or presence detection : Monitoring process active

ORANGE LED

See chapter 5: Troubleshooting

Tips

Use the Remote-Control to

adjust the sensor.

Use the Spotfinder to locate

the safety curtains.

Avoid touching electronical

parts!

Avoid touching optical

parts!

Make sure the operator

cover is fixed properly and

electrically earthed.

Avoid vibrations!!!

Do not cover the sensor!

Avoid moving objects in

proximity to the sensor!

Avoid HF lamps and

fluorescent lighting in the

infrared field!

Avoid highly reflective

objects in the infrared field!

1 Description

3 Installation

2 Symbols

Summary of Contents for BEA ACTIV8 THREE ON









Search results

Summary of Contents for BEA ACTIV8 THREE ON

Reviews:

Related manuals for BEA ACTIV8 THREE ON

Brands by name

Popular brands

Halma BEA ACTIV8 THREE ON, User Manual

Search results

Summary of Contents for BEA ACTIV8 THREE ON

Reviews:

Related manuals for BEA ACTIV8 THREE ON

Brands by name

Popular brands