Haas ATT-4 Installation And Alignment Manual Download

Page: 1 / 10

LAST UPDATED: 02/18/2019

TL-1/2 - ATT-4/8 Turret - Installation and Alignment

AD0304

Applies to machines built September 2014 and after

Introduction

This procedure tells you how to install a ATT-4/8

turret on a TL-1 or TL-2 lathe.

Software Requirements:

• Classic Haas Control (CHC) - Software

version 11.24A or higher.

• Next Generation Control (NGC) -

Software 100.17.000.2040 or higher.

Tools Required

• 0.0005" Dial Indicator with Magnetic

Base

• Service USB key (NGC only)

Document Applies to these kits:

• 93-2228 TL-1/2 ATT4 Standard - CHC
• 93-2229 TL-1/2 ATT4 Metric - CHC
• 93-3833 TL-1/2 ATT4 Standard - NGC
• 93-3834 TL-1/2 ATT4 Metric - NGC
• 93-2899 TL-1/2 ATT8 Standard - NGC
• 93-2898 TL-1/2 ATT8 Standard - NGC

TL-1/2 - ATT-4/8 Turret - Installation and Alignment - AD0304

Page 1 of 10 pages

Summary of Contents for ATT-4











Search results

Summary of Contents for ATT-4

Reviews:

Related manuals for ATT-4

Brands by name

Popular brands

Haas ATT-4, Installation And Alignment Manual

Search results

Summary of Contents for ATT-4

Reviews:

Related manuals for ATT-4

Brands by name

Popular brands