background image

©

2007 GTO, Inc.

Installation Manual for the

WARNING!

This equipment is similar to other gate or door equipment and meets or exceeds 

Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has 

hazards associated with its use and therefore by installing this product the installer 

and user accept full responsibility for following and noting the installation and 

safety instructions. Failure to follow installation and safety instructions can result 

in hazards developing due to improper assembly. You agree to properly install this 

product and that if you fail to do so GTO, Inc. shall in no event be liable for direct, 

indirect, incidental, special or consequential damages or loss of profits whether 

based in contract tort or any other legal theory during the course of the warranty 

or at any time thereafter. The installer and/or user agree to assume responsibility 

for all liability and use of this product releasing GTO, Inc. from any and all 

liability.  If you are not in agreement with this disclaimer or do not feel capable 

of properly following all installation and safety instructions you may return this 

product for full replacement value.

READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before 

attempting to install and use this automatic gate opener.  This gate opener 

produces a high level of force.  Stay clear of the unit while it is operating and 

exercise caution at all times.

All automatic gate operators are intended for use on vehicular gates only and 

should never be used by pedestrians.

This product meets and exceeds the requirements of UL 325, the standard which regulates gate opener safety, 

as established and made effective March 1, 2000, by Underwriters Laboratories Inc.

 

R2502INST

     

re

v - 04/

8/07

GTO/PRO • 3121 Hartsfield Road • Tallahassee, Florida, USA 32303

Telephone GTO/PRO Sales: 1-800-543-GATE (4283) or (850) 575-0176 • Fax (850) 575-8912

or GTO/PRO Technical Service: 1-800-543-1236 or (850) 575-4144 • Fax (850)575-8950

www.gtopro.com­

Dual Automatic Gate Operators

L I S T E D

US

Summary of Contents for SW-2502












































Reviews: