ti11784a
ENG
T-Max Applicator
Model: 256383
US Patent No. D588,230 S
Maximum Fluid Working Pressure: 1,000 psi (6.9 MPa, 69 bar)
Maximum Air Working Pressure: 250 psi (1.7 MPa, 17 bar)
-
For Water-Based Materials Only -
The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point
symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings.
Additional, product-specific warnings may be found throughout the body of this manual where applicable.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the applicator/dispense valve, leaks, or
ruptured components can splash in the eyes or on
skin and cause serious injury.
• Follow
Pressure Relief Procedure
in this manual, when
you stop spraying and before cleaning, checking, or ser-
vicing equipment
.
• Tighten all fluid connections before operating the equip-
ment.
• Check hoses, tubes, and couplings daily. Replace worn
or damaged parts immediately.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes,
in
work area
can ignite or explode. To help prevent
fire and explosion:
• Keep work area free of debris, including solvent, rags
and gasoline.
• Ground all equipment in the work area. See
Grounding
instructions.
• If there is static sparking or you feel a shock,
stop oper-
ation immediately.
Do not use equipment until you iden-
tify and correct the problem.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influ-
ence of drugs or alcohol.
• Do not exceed the maximum working pressure or tem-
perature rating of the lowest rated system component.
See
Technical Data
in all equipment manuals.
• Use fluids and solvents that are compatible with equip-
ment wetted parts. See
Technical Data
in all
equipment
manuals. Read fluid and solvent manufacturer’s warn-
ings. For complete information about your material,
request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or dam-
aged parts immediately with genuine manufacturer’s
replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your
distributor for information.
• Route hoses and cables away from traffic areas, sharp
edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull
equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment
when operating, servicing, or in the operating area of
the equipment to help protect you from serious
injury. This equipment includes but is not limited to:
• Protective eyewear and hearing protection
• Clothing and respirator as recommended by the fluid and
solvent manufacturer
• Gloves
Pressure Relief Procedure
Follow this
Pressure Relief Procedure
whenever instructed to relieve pressure,
stop spraying, check or service equipment,
or install or clean spray tip.
1.
Turn OFF power and turn sprayer pressure control to
lowest pressure setting.
2.
Hold applicator against side of hopper. Open applicator
into hopper to relieve pressure.
If you suspect spray tip or hose is clogged or that pressure
has not been fully relieved after following the steps above,
slowly loosen retaining nut at base of pump to relieve
pressure gradually. Clear hose or tip obstruction.
WARNINGS
WARNING
312879D
IMPORTANT SAFETY INSTRUCTIONS.
Refer to your
sprayer instruction manual for Pressure Relief, priming and
spray instructions. Keep these instructions.
Instructions/Parts
English
Indian Patent No. 218331
Chinese Patent No. ZL200830142725.X
European Registered Design No. 000996236-0001
Japanese Patent No. 1380673
Korean Patent No. 30-556464
Окрасочное оборудование GRACO
