![background image](http://html.mh-extra.com/html/global-industrial/246110/246110_assembly-instructions_2233003001.webp)
WALL THERMOSTAT
Model: 246110
READ CAREFULLY
-
These instructions will help prevent difficul-
ties that might arise during thermostat installation.Studying the instruc-
tions first may save considerable time and money later.Observing the
following procedures will keep installation time to a minimum.Save these
instructions for future use.
READ ALL WIRE SIZING, VOLTAGE RE-
QUIREMENTS AND SAFETY DATA TO
AVOID PROPERTY DAMAGE AND PER-
SONAL INJURY OR ELECTRIC SHOCK.
READ AND SAVE THESE INSTRUCTIONS
L1 from
power supply
Neutral from
power supply
Line
Red
Load
Black
Thermostat
Wire Connector
Heater
Double Pole Thermostat Installation
1.
Disconnect power supply to prevent electrical shock or
damage to product.
2.
Run line voltage wiring to the thermostat location.
3.a)
Connect the LOAD BLACK wire from the thermostat to
the one of wires from the heating unit.
b)
Connect another black wire from the thermostat to
another wire from the heating unit.
4.a)
Connect the LINE RED wire on the thermostat to the
L1 line from the supply panel.
b)
Connect another red wire from the thermostat to
another wire from the supply panel.
5.
Make sure all connections are tight.
6.
Insert wires into the junction box, making sure not to
damage wiring.
7.
Secure the ground wire to the ground screw provided in
junction box.
8.
Remove the thermostat cover by grabbing the cover from
the sides and pulling it away from base.
9.
Mount the thermostat into the junction box and secure
using the provided screws.
10.
Replace thermostat cover.
The installation of the thermostat must comply with the ap-
plicable local and/or national electrical code and utility re-
quirements. This installation should be performed by a
qualified electrician where required by law. Ensure that all
wiring connections to the thermostat are correct and tight to
prevent electrical shorts. Use the appropriate wire to meet
local and national electrical codes for rated power consump-
tion.
Product Setup and Settings
To adjust the temperature to your requirements, turn the dial
on the thermostat clockwise all the way to turn heater on.
When the room reaches the desired temperature, turn the
thermostat knob counter clockwise until you hear the click.
Leave in this position to maintain the room temperature at
this setting. For additional heat, turn clockwise until you
hear the click and the heater will turn on.
- Turning knob fully counter clockwise will disconnect the
power to the heater.
Changing °C and °F control dials.
Use a small flathead screwdriver to pry off the control dial.
Insert into one of the slots on the dial and gentle apply pres-
sure to remove.To install the new control dial, line up the
pins on the dial with the holes on the thermostat knob. Push
together until secured into place.
Specifications:
Thermostat is compatible with electric heaters and electric
garage heaters
Power Supply AC 120V / 208V / 240V / 277V Maximum
Power:
3360W @ 120VAC (28A)
5824W @ 208VAC (28A)
6720W @ 240VAC (28A)
7756W @ 277VAC (28A)
Sensing Element: Bimetal Temperature Operating Range:
41°F-90°F (5°C -32°C)
cETLus listing.
Functions And Features
• 120/208/240/277 Volts
•Includes both ºC and ºF control dials
•Wall mount design– Sits flush against wall
•Double Pole – provides positive OFF position
•Disconnects power for extra protection
•Large knob allows easy adjustment to all temperatures
•90°F (32°C) maximum setting
Installation Instructions
Cover
Screw
Index Plate
Base
Outlet Box
Warning:
Turn OFF the power at the circuit breaker before
installing. Installation should be performed by a qualified
electrician.
Refer to thermostat and heater load specifications before
installation of the thermostat to see if it can handle the
amp load. The maximum this thermostat can run is 7756
Watts at 277 Volts, 6720 Watts at 240 Volts, 5824 Watts at
208 Volts and 3360 Watts at 120 Volts.
Install unit in a grounded metal or plastic wall junction box,
indoors 4 ½’ to 5’ above the floor. Avoid any area where it
can come in to contact with external sources of heat and
cold. This includes plumbing pipes, direct sunlight, a T.V.
set, lamps, and drafts from a door or window, as this may
cause inaccurate temperature readings. The most conven-
ient place is above the light switch. Not for outdoor use.