background image

1

,QVWDOODWLRQ,QVWUXFWLRQV

ZZZJHVHFXULW\FRP

*(6HFXULW\

'

Product 
Summary

These touchpads let you control all programming and operation of compatible security systems 
(see the “Specifications” section).

The large 2-line, 16-character displays provide easy to read messages to indicate the current sta-
tus of the system. Both touchpads include police, fire, and auxiliary panic buttons that can be 
activated anytime. A built-in sounder provides alarm, status, and button-press sounds. The ATP 
2100 includes a swing-down door that reveals the buttons and a label with basic system operat-
ing commands. The ATP2600 has a flip-top that hides the display and covers the buttons when 
down. Both touchpads also include menu scroll buttons to the right of the display and a hardwire 
contact input.

Tools and Equipment Needed

4-conductor, 22- or 18-gauge wire

Screwdriver

#6 screws and anchors (included)

Panhead screws for gang box installation

Saw or utility knife for cutting wallboard

Installation

Guidelines

Mount the touchpads in an environmentally controlled area (32°F to 120°F/0°C to 49°C).

When mounting the ATP2100, allow at least 3 inches below it for the swing-down door.

When mounting the ATP2600, allow at least 2 inches above it for the flip-top display.

Do not exceed the maximum available power (see panel 

Installation Instructions

).

Table 1 describes the power used by the touchpads.

Table 2 describes the maximum wire lengths allowed between the touchpad and the panel.

0RGHO1R$73

0RGHO1R$73

Table 1: Touchpad Power Usage

Current (mA)

Conditions

165

Maximum alarm current with the 
buzzer sounding and the touchpad 
illuminated from a button press

110

Typical operation

30

Power saving mode (no panel AC 
power)

Table 2: Maximum Touchpad Wire Lengths

Wire Gauge 

(Unshielded or 

Shielded)

Max. Power & Bus Wire 

Length to Panel

Wire Gauge 

(Shielded)

Max. Hardwire Input 

Wire Length

18

750 feet

18

1000 feet

22

300 feet

22

350 feet

'RFXPHQW1XPEHU5HY&

6HSWHPEHU

$73 $737RXFKSDGV

Summary of Contents for ATP2100







Reviews: