Safety harness is basic fall arrest equipment complied with EN 361.
DESCRIPTION
Full body harness P-34EL is made of polyester/polyamide 45 mm
wide webbings which are sewn and connected by metal buckles.
This configuration guarantees full safety and comfort work.
BASIC EQUIPMENT
!
back attaching buckle - for attaching fall arrest systems
!
connecting and adjusting buckles - for comfort wearing and using
of harness
!
front attaching buckle - for fall arrest sysytems
SIZES
The harness P-34EL is manufactured in two sizes:
- universal: M-XL
- extra large: XXL
shoulder strap
adjusting
buckle
of the shoulder
strap
connecting
buckle
of the chest
strap
back attaching
buckle for attaching
fall arrest system
front attaching
buckle for attaching
fall arrest system
connecting
and adjusting
buckle
of the thigh
strap
thigh strap
SAFETY HARNESS
Ref. AB 134 03
Size:
Date of manufacture: MM / YYYY
Serial number: XXX XXX
M-XL
XXL
EN 361:2002
P-34EL-QR
CONTENT OF HARNESS IDENTITY LABEL
number of the manufacturing series
CE marking and number of a notified body
controlling manufacturing of the equipment (art. 11)
type of the device
reference number
month/year of the device manufacture
marking of the manufacturer
or distributor
trade mark of the device
size
caution: read the manual
!
regular periodic inspections are the essential for equipment maintenance and the safety of the users which depends upon the continued efficiency and durability of the equipment.
!
during periodic inspection it is necessary to check the legibility of the equipment marking.
!
it is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller shall provide instructions for use, for maintenance, for periodic
examination and for repair in language of the country in which the product is to be used.
!
personal protective equipment must be withdrawn from use immediately when any doubt arise about its condition for safe use and not used again until confirmed in writing by
equipment manufacturer or his representative after carried out the detailed inspection.
!
personal protective equipment must be withdrawn from use immediately and destroyed (or another procedures shall be introduced according detailed instruction from equipment
manual) when it have been used to arrest a fall.
,
!
a full body harness is the only acceptable body holding device that can be used in a fall arrest system.
!
the anchor device or anchor point for the fall arrest system should always be positioned, and the work carried out in such a way, as to minimise both the potential for falls and potential
fall distance. The anchor device/point should be placed above the position of the user . The shape and construction of the anchor device/point shall not allowed to self-acting
disconnection of the equipment. Minimal static strength of the anchor device/point is 12 kN.
I
t is recommended to use certified and marked structural anchor point complied with
EN795.
!
it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest system, so that, in the case of a fall, there will be no
collision with the ground or other obstacle in the fall path. The required value of the free space should be taken from instruction manual of used equipment.
!
there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization, especially:
- trailing or looping of lanyards or lifelines over sharp edges
;
- any defects like cutting, abrasion, corrosion
;
- climatic exposure
;
- pendulum falls
;
- extremes of temperature
;
- chemical reagents
;
- electrical conductivity.
!
personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of steel or plastic) to protect it against damage or
moisture.
!
the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use mild detergents for delicate fabrics, wash by
hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be
allowed to dry naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly slightly lubricated to ensure better
operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
!
personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation, damp environment, sharp edges, extreme
temperatures and corrosive or aggressive substances.
IDENTITY CARD
PERIODIC EXAMINATION AND REPAIR HISTORY
DATE
REASON FOR
ENTRY PERIODIC EXAMINATION
OR REPAIR
SERIAL NUMBER
USER NAME
DATE OF MANUF.
DATE OF PUTTING
INTO OPERATION
DATE OF PURCHASE
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS
REQUIRED. THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE
USER ORGANIZATION FOR PROTECTIVE EQUIPMENT. ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC
INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWAL FROM USE SHALL BE NOTED INTO THE IDENTITY CARD
BY A COMPETENT PERSON.
MODEL AND
TYPE OF EQUIPMENT
REF. NUMBER
DEFECTS NOTED,
REPAIRS CARRIED OUT
AND OTHER REVELANT INFORMATIONS
NAME AND SIGNATURE
OF COMPETENT PERSON
PERIODIC
EXAMINATION
NEXT DUE DATE
number / year of the European standards
the equipment conform
Ref.: AB 134 03
Instruction Manual
READ CAREFULLY BEFORE USE
THE EQUIPMENT
SAFETY
HARNESS
P-34EL-QR
EN 361:2002
Periodic inspections
The harness must be inspected at least once every 12 months from the
date of first use.
Periodic inspections must only be carried out by a competent person
who has the knowledge and training required for personal protective
equipment periodic inspections.
Depending upon the type and environment of work, inspections may
be needed to be carried out more frequently than once every 12
months.
Maximum lifespan of the equipment
The maximum lifespan of the harness is 10 years from the date of
manufacture. This is irrespective of shelf life and working life
The harness must be withdrawn from use immediately and destroyed
when it has been used to arrest a fall.
identity label
No.
SafetyLiftinGear.com
Unit R1D Rockingham Gate Poplar Way
West Cabot Park Bristol BS11 0YW
Tel: 0808 123 69 69 Fax: 0117 9381 602
Notified body, at which the European certification was
performed and which supervises
the production of the equipment:
APAVE SUDEUROPE SAS - BP 193 -
13322 MARSEILLE CEDEX 16 - FRANCE
