![background image](http://html1.mh-extra.com/html/frsky/archer-r10-pro/archer-r10-pro_instruction-manual_2340143001.webp)
Instruction Manual for FrSky ARCHER GR8 Receiver
Version
1.0
LED state
Green LED
On
Flash
On
On
On
Off
Red LED
On
Flash
On
Off
Off
On
Status
Register
Register successfully
Bind
Bind successfully
Working normally
Failsafe
Version
1.0
Instruction Manual for FrSky ARCHER R10 PRO Receiver
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
01140166
Introduction
The Archer R10 Pro has 10 high-precision PWM channel outputs and features excellent Anti-interference
performance when it comes to spark-ignition on internal combustion models. It supports full-range signal strength
with dual detachable antennas that assure optimal antenna reception and maximum range. In addition to all this, the
R10 PRO can also be used as a redundancy receiver along with any other FrSky ACCESS capable receiver
equipped with a SBUS port. This 10-channel receivers’ noticeable features are its Anti-vibration performance and
dual-battery ports for redundancy.
All of the Archer receivers are hyper-matched with the ACCESS protocol. They not only feature wireless firmware
upgrades, increased range, and telemetry performance, the R10 PRO now supports more functions like configu-
rable telemetry power, S.Port/F.Port switching and FLR output. Additional valuable features are under development
to unlock the true potential of the ACCESS protocol.
Overview
SBUS OUT
SBUS IN
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
VB
AT
VB
AT
INP
UT:DC 3.
5V~10V
LED
2
R 1 0 P r o
1 0 / 2 4 C H T e l e m e t r y
BUTTON
Warning: Do not plug the additional
power supply in other port (Channel,
S.Port, SBUS, etc.)
while using dual
battery to power the receiver.
Registration & Automatic binding (Smart Match )
With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "REG"
button.
Follow the step below to finish the Registration & binding procedure:
1. Put the transmitter/transmitter module into [Reg] status.
1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2,
choose Internal or External RF, and select [Reg].
TM
Specifications
●
Dimension: 48.5*33*17mm (L*W*H)
●
Weight: 21g
●
16/24 Configurable SBUS Channels
●
10 High-precision PWM Channels
●
Operating Voltage Range: 3.5-10V
●
Operating Current: 80mA@5V
●
Battery ports: XT30
● Control Range: Full range* with telemetry
(*Full Range:
>
2km, range may vary based
on local conditions.)
● Voltage Measurement Range via AIN2
(External device): 0-36V
(Battery Voltage Division Ratio: 1:10
)
● Compatibility: All FrSky ACCESS transmitters
Features
● ACCESS protocol with Over The Air (OTA)
● Supports signal redundancy (SBUS In)
● Supports power redundancy (Dual battery ports)
* it will automatically be powered by the one with
highervoltage.
● S.Port / F.Port
● Anti-interference in spark-ignition
● Anti-Vibration
● External battery / device voltage detection
● VFR (Valid Frame Rate) telemetry