background image

 

 

Instructional Supplement for  
Full-Body Harness with High-Vis Vest

 

 

Section 1:  Warnings  

 

 

 

Before using this product, the user must read, 
understand and comply this supplement as well as the 
Instructions for Full Body Harnesses also included with 
this product.  Failure to comply with the instructions, 
labels and warnings provided with this product may 
result in serious injury or death. 
 
If you have any questions about the safe and proper use 
of this product, or any element of your Personal Fall 
Arrest System, seek immediate assistance from a 
competent person or supervisor

 

Section 2:  Use and Limitations 

 

This product is designed to provide a level of enhanced 
visibility for workers who are exposed to fall hazards in 
environments where vehicular traffic, the operation of 
heavy equipment and other activities or conditions may 
pose a hazard as well.  7018-series model #’s meet or 
exceed the requirements of ANSI/ISEA 107-1999 for Class 
II high-visibility. 
 
Based upon your application, other protective clothing or 
personal protective equipment may be required – see a 
competent person or supervisor for assistance if you have 
questions about your equipment. 

 

2.1 – General Use 

 

All FallTech High-Vis Vest Harnesses can be used for fall  
arrest and travel restraint.  7018-series model numbers 
may also be used for work positioning.  See Section 2 and 3 of 
the FBH Instructions for details

 

2.2

 

- Donning and Adjustment 

 

Before donning and adjusting your Vest Harness, inspect the  
product in accordance with Section 8 of your FBH  
Instructions and ensure that the vest is properly attached and  
secured.  See figure 1. 

 

1.

 

Lift the harness by the back D-ring and untangle the 
straps, allowing the leg straps to hang free. 

2.

 

Don the vest harness as you would a jacket, 
ensuring that the back D-ring is between your 
shoulder blades.  See figure 2. 

3.

 

Fasten the chest strap buckle. 

4.

 

Fasten both leg straps – they should be adjusted to 
be snug, but not tight. 

5.

 

Adjust the chest strap and right and left torso strap 
adjusters so that the harness fits snug, but not tight. 

6.

 

Zip up the vest and proceed to your work location.  
See figure 3 of this supplement and Section 3.5 of 
your FBH Instructions for details. 

 

2.3 - Leg Strap Stash Pouch 

 

If you will not be exposed to any fall hazards, and will not be 
tied- off, the leg straps may be unfastened and stashed in the 
inner pouch in the back of the vest.  See figure 4. 
 

Warning:  Never attempt to tie-off with the leg straps 
stashed.  Always ensure that all straps are fastened and 
properly adjusted prior to tying off.  Failure to do so may 
result in serious injury or death. 

 
2.4 - Lanyard Keeper 
 

7018-series model numbers are equipped with a single lanyard 
keeper.  See figure 5 for details. 

 
Warning:  Never use a hip or side D-ring as a lanyard 
keeper (to stow the second leg of a dual-leg lanyard).

 

 

2.5

 

- Tying Off 

 

See Section 3 of your FBH Instructions. 

 

Section 3:  Inspection, Maintenance and Storage 

 

This product must be thoroughly inspected by the user before 
each use.  Refer to Section 8 of your FBH Instructions for 
critical inspection details and procedures.  If this product does 
not pass the inspection, immediately remove it from service 
and have it replaced.  

Failure to do so may result in serious 

injury or death. 

 
Your full-body harness (FBH) should maintained and stored in 
accordance with Section 9 of your FBH Instructions.  The vest 
may be hand-washed in a light solution of soap and water and 
should be hung and allowed to air dry.  Re-attach the vest as 
shown in figure 1. 

 
 
 

MFBH02 ALX 

Summary of Contents for 70182X3XO









Reviews: