1
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
DTP DVI 330 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the Extron DTP DVI 330 digital video
extender. The DTP DVI 330 transmitter and receiver pair can extend an HDCP-compliant DVI signal up to 330 feet (100 m).
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.
Step 2 — Connections
a
DVI Input connector (Tx)
— Connect an DVI cable
between this port and the DVI output port of the digital video
source.
b
Local Output connector (Tx)
— If desired, connect a DVI monitor for local monitoring of the input digital image.
c
Audio input (Tx)
— Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.
d
RS-232 and IR connectors
(both units) — To pass serial or infrared data or control signals,
such as serial control of a projector, connect the primary device to the transmitter and the
secondary device to the receiver via the RS-232 and IR captive screw connectors on both
units.
e
DTP RJ-45 connectors
(both units) — Connect transmitter DTP Out to receiver DTP In.
Extron recommends that you terminate both cable ends in accordance with the following
specifications, at a minimum:
•
TIA/EIA T 568 B
•
CAT 6A, shielded
•
24 AWG, solid conductor
ATTENTION:
•
Do not connect these devices to a computer data or telecommunications network.
•
Ne connectez pas ces appareils à un réseau de télécommunications ou de données
informatiques..
Sig(nal) LED
(both units) — Lights when the unit is receiving a TMDS clock signal on the DVI input
(transmitter) or any valid signal on the DTP In connector (receiver).
Link LED
(both units) — Lights when a valid link is established between the units on the DTP cable.
f
DVI Output connector (Rx)
— Connect a display with an DVI input for display of the transmitted direct digital image.
g
Audio Output connector (Rx)
— Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio
captive screw connector. See the
drawing
on page 2.
DTP DVI 330 Tx
DTP DVI 330 Rx
L
R
OUTPUTS
DVI-D
AUDIO
DTP DVI 330 Rx
INPUTS
LOCAL OUTPUT
AUDIO
DVI-D
DTP DVI 330 Tx
Rx G
Tx
RS-232
IR
Rx
Tx
POWER
12V
0.8 A MAX
SIG LINK
DTP OUT
OVER DTP
Rx
G
Tx
RS-232
IR
Rx
Tx
POWER
12V
0.8 A MAX
SIG LINK
DTP IN
OVER DTP
LOCAL
SHARE
REMOTE
1 2
ON
DDC ROUTE
Front
Rear
4
8
8
1
5
2
3
Front
Rear
4
7
6
5
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T
568 B
TP Wires
12345678
Pins:
Ground
Receive pin on connected unit
Transmit pin on connected unit
Connected RS-232
and IR Device Pins
Tx/Rx
Pins
Receive pin on connected unit
Transmit pin on connected unit
Rx
G
Tx
RS-232
I
R
Rx
Tx
