background image

1

G Series

 Linear Hearth Burner                  

                                                                                                                                                        European

Home

.com

-- Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do 

not use any phone in your building.

•  Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions.

•  If you cannot reach your gas supplier, 

call the fire department.  

-- Installation and service must be performed by 

a qualified installer, service agency or the gas 

supplier.  

WARNING: If the information in these 

instructions is not followed exactly, a fire 

or explosion may result causing property 

damage, personal injury or loss of life.

This is an unvented gas-fired heater. It uses 

air (oxygen) from the room in which it is 

installed. Provisions for adequate combustion 

and ventilating air must be provided. Refer to 

page 6.

INSTALLER: Leave this manual with the 

appliance.

CONSUMER: Retain this manual for future 

reference.

This appliance may be installed in an aftermarket, 

permanently located, manufactured (mobile) 

home, where not prohibited by local codes.
This appliance is only for use with the type of 

gas indicated on the rating plate. This appliance 

is not convertible for use with other gases.

G   S E R I E S

L i n e a r   ·   H e a r t h   ·   B u r n e r

Installation, 

Operation

and

Owner’s Manual

GVF-42

GVF-60

GVF-72

January 6, 2016

Report  #284-F-08-4  

Summary of Contents for GVF-42

































Reviews: