Liebert
®
PSP
™
Quick-Start Guide - 500VA/650VA, 230V
I
MPORTANT
S
AFETY
I
NSTRUCTIONS
• Do not connect equipment that may overload the UPS or demand half-wave
rectification, such as a laser printer.
• Connect the UPS only to an earthed / grounded socket that meets electrical safety
guidelines.
• Locate the UPS near a wall socket. Do not use an extension cord between the UPS and
the socket.
• Use CE-marked cables only for connections between mains, the UPS and equipment.
• The Liebert PSP has been designed for small office/home office use only; it is NOT
recommended for use in life-support applications.
• In the event of an emergency, press the On/Off button and disconnect the power cord
from the AC mains to properly disable the UPS.
• Do not attach power strips or surge suppressors to the UPS.
• Do not attempt to service any parts inside the UPS except when replacing the batteries.
Failure to adhere to this could cause personal injury or equipment malfunction and void
the warranty.
• This unit uses components that are dangerous for the environment, such as electronic
cards and other electronic components. Any component that is removed must be taken
to specialized collection and disposal centers. If this unit must be dismantled, this must
be done by specialized personnel who are properly trained and qualified. The unit must
be taken to a center specialized in collection and disposal of dangerous substances.
• For technical support:
• Visit
www.liebert.com
or
• Send an e-mail to
.
S
ETUP
UPS C
ONTROLS
AND
C
ONNECTIONS
Step 1 Inspect the Package
Inspect the package and the UPS upon receipt.
Notify the carrier and dealer of visible damage.
The package includes:
• Liebert PSP
• USB cable
• Quick-start guide
• 2 IEC output cables
The Liebert MultiLink™ software may be
downloaded from the Liebert Web site at:
multilink.liebert.com
See
Step 7
for installation instructions.
Step 2 Decide Where to Place the UPS
The UPS must be placed indoors, protected from water, direct
sunlight and excessive heat.
Provide at least 100mm (4") of clearance on all sides of the unit
for proper ventilation.
Step 3 Charge the UPS Battery Before Use
The UPS battery is not charged before shipping. It MUST be charged before use.
• Use the input power cord from computer equipment as the input power cord of UPS.
Connect a user-supplied power cord from the UPS to a wall socket and charge for at
least eight hours. Unit can be charged in the on or off state.
Note:
If battery is placed in storage, charge the battery every six months if kept at
-15°C to +29°C (5°F to 85°F)—or every three months if kept at 30°C (86°F) or higher.
Step 4 Start the UPS
After the battery is fully charged:
• Turn on the UPS by pressing the On/Off button (see
Figure 1
below).
LED 1 should be illuminated (green), indicating the UPS is operating in Normal Mode.
Step 5 Connect the Loads
The UPS has three battery backup sockets that
provide power when the UPS operates on bat-
tery. There is also one surge-only socket (see
Figure 2
below).
• Plug the loads into the battery backup
sockets on the rear of the UPS.
Caution:
Do not connect a laser printer to the
UPS.
Step 6 Connect the Network Surge Protection
The UPS has two network cable jacks for network lines
(see
Figure 2
below).
• Connect a single-line network cable into the network
surge protection IN jack on the rear of the UPS.
• Connect a network cable from the OUT jack on the
rear of the UPS to a port on a PC or network device
such as a router.
Step 7 Set Up Liebert MultiLink software
To start using the Liebert MultiLink software:
• Install the software.
See the Liebert MultiLink quick-start guide or user manual
for installation instructions.
• Connect one end of the USB cable (supplied) to the USB
port on the rear of the UPS. Connect the other end to a
USB port on the computer.
See the Liebert MultiLink user manual for operating instructions.
Note:
Emerson recommends connecting the USB cable directly to the computer
WITHOUT using a USB hub.
USB
cable
Quick-
start
guide
UPS
2 IEC
output
cables
!
EMERSON
™
Network Power
Liebert
®
PSP
AC Power System
UPS Status, Alarm Conditions and Alerts
Condition
LED
Color
Solid/Flashing
Audible Alarm
Normal Mode
LED 1
Green
Solid (steady glow)
(None)
Battery Mode
LED 1
Green
Flashes every 3 seconds
Every 3 seconds
Battery Low
LED 1
Green
Flashes every 1 second till end of discharge (EOD)
Every 1 second
Overload
LED 2
Amber
Solid (steady glow) until load drops or breaker trips
Continuous
Battery Replacement
LED 2
Red
Flashes every 1 second for 5 seconds only
Every 1 second for 5 seconds only
Fault
LED 2
Red
Solid (steady glow) until UPS shuts down after 5 seconds
Continuous until UPS shuts down
Figure 2 - Rear Panel
AC mains
inlet
Figure 1 - Front Panel LEDs
Battery backup
sockets (3)
IEC 320 C13
RJ-45 jacks (2)
Network
protection
USB
interface
Surge socket (1)
IEC 320 C13
Mains
breaker
LED 2 (red = fault;
amber = overload)
Fault
symbol
Overload
symbol
Mains
symbol
On/Off button
LED 1
(green)
