Warning!
Important safety instructions!
Observe the following instructions.
Risk of injury due to electric shock.
The connections to the 230 V mains
must
be made
by authorised specialist personnel.
Check the system (awnings) regularly for wear or
damage.
The regulations of the local energy supply company
as well as the regulations for wet and damp rooms
according to VDE 0100 must be followed when
making the connections.
Only use unmodified original
elero
parts.
Keep people away from the system until it is
stationary.
When working on the system (servicing, cleaning
windows etc.), always disconnect it from the mains
supply.
Check the following before installation:
• The drive is only capable of operation as installed.
• Only perform connecting work with the power turned off.
• The blind must be attached to the winding shaft.
• The profile tube must have sufficient clearance from the motor
tube.
• Make sure there is sufficient axial play (1–2 mm)
Device functions:
• Commissioning of the drive using assembly cable or radio
transmitter
Delivery condition
(commissioning mode)
• Setting the end positions
Keep these instructions in a safe place!
After installation of the motor attach these instructions
to the cable for the electrician.
Warning!
Installation in profile tubes
Ⓐ
Push drive with relevant adapter and
limit switch crown into the profile
tube.
Lay the motor cable so that it is
protected, do not kink.
Ⓑ
Secure the counterpart support to
prevent axial movement,
e.g. screw or rivet on the idler.
Secure the drive axially in the
support!
Ⓒ
Attach the blind to the shaft!
B
A
C
Intended use
• Please ensure that the radio installations are not operated in
areas of increased possible interference.
(e.g. hospitals, airports ...).
• The radio control is only permitted for devices and units with which
a functional interference in hand-held/wall-mounted transmitters
or receivers poses no danger for persons, animals or materials or
where this risk is covered by other safety appliances.
• The operator has no protection whatsoever from interferences
by other radio emitters and local terminals (e.g. also from radio
installations), that are normally used on the same frequency
range.
• Only use radio receivers with equipment and units approved by
the manufacturer.
Optimal use of the radio signal
• Do not bend the antenna.
• Do not shorten or extend the antenna.
• If reception is poor, adjust the antenna.
• Install the antenna so that it is as exposed as possible.
• The minimum distance between two radio drives must be at
least 15 cm.
Warning!
Installation
Observe the following installation instructions!
– The drive must be fixed in such a way that it does
not endanger personnel.
– Before installing the drive, all lines and equip-
ment, which are not required for operation, must
be removed from the site.
– During installation, during operation and when
work is carried out on the system, the option to
separate all poles from the mains must always
exist (Hirschmann connector and Hirschmann
coupling or a two-pole switch with minimum 3 mm
contact gap or all-pole main switch).
– If the drive is controlled by a switch with OFF
pre-setting (dead man’s button), the momentary
contact switch must be fitted at a height of more
than 1.50 m and separated from the moving parts.
The travel range of the systems must always be
visible during operation.
– Moving parts in a drive, which are below 2.5 m,
must be protected.
– Set torque and set operating time must meet the
requirements of the product which is driven.
– Please note the technical data on the type plate.
– Please note that with this drive (type 11 M motor)
the smallest internal tube diameter corresponds
with 47 mm.
– The drive must be installed so that it cannot get
wet.
– Do not install drives in surroundings which are at
risk of explosion or in mobile appliances
(e.g. motor vehicles).
– Keep children away from the (remote) control unit.
Risk of injury due to electric shock.
Do not drill in the area of the motor!
138134201_EN_0413
Awning drive SunTop-868
