background image

1/

18 

 

 

 

 

 

OFM103-NG

 

Amish 

Table owner’s manual 

 

 

  If the information in this manual is not 

follow exactly, a fire or explosion may 
result causing property damage 
personal injury or loss of life 

Read  the  in

stallation,  operation 

and  maintenance  instructions 
tho

roughly  before  installing  or 

servicing this equipment.

 

 

Installation and service must be

 

performed by a qualified installer, 
service agency or gas supplier.

 

 

 

Improper installation, adjustment,

 

alteration, service or maintenance can 
cause injury or p

roperty damage. 

Save these instructions for future

 

reference. If you are assembling 
this unit for someone else, give 
this manual to him or her to read 
and save for future reference.

 

DANGER

 

If you smell gas:

 

Shut off gas to the appliance.

 

Extinguish any open flame.

 

If odor continues, keep away 

from the appliance and 
immediately call your gas supplier 
or fire department.

 

WARNING

 

Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance.

 

This unit is not for use with 

propane. Use only with Natural 

gas.

 

WARNING

 

For outdoor use only. DO NOT use 
for cooking. DO NOT use under any 
overhead enclosure.

 

IMPORTANT

 

SAVE THESE 

INSTRUCTIONS

 

Summary of Contents for OFM103-NG



















Reviews: