Solar Powered LED Smart Street/Parking Lot Lighting
12346 Valley Blvd, El Monte, CA 91732 USA
Phone Number: 1-877-579-3889 Fax Number: (626) 452-9194 www.eesgi.com /www.eleding.com/
Rev: 11162016
EE Systems Group Inc.
2
-1
Installation Instruction
eLEDing
®
/ EE800W-SH series
Thank you for choosing eLEDing!
Introduction and Intellectual Property Rights Statement
This product is designed to provide years of trouble-free services by using environment-friendly Solar-Hybrid-Lithium based energy
technologies. Covered under US, European, China and other international patents granted and pending worldwide. All rights reserved.
The performance of this unit is highly related to its mounting location, direction of the solar panel, weather conditions and local environment.
Therefore, to maximize the performance of the unit, user(s)/installer(s) must read this instruction before installation. DIY user(s) must have
knowledge on AC/DC electric/electronic projects and related construction/installation experiences. Otherwise, user(s) should consult with
local experienced electrical & electronics installers or technicians for assistance. Before installation, user(s) should be aware of and comply
with local construction laws, electrical code and life & safety standards/regulations that are applied for this lighting project. During
installation, please follow proper safety guidelines to prevent any possible accidents or injuries.
Initial Function Testing:
The purpose of this step is to ensure the light unit and control system as well as every component are all function
and in normal working condition. This light unit had been fully charged before shipping out, but switch OFF to pre-charge it by Sunshine
condition for 1-2 days before in use will be recommended.
Only One Step Setup:
Momentary press on the button/switch once (Fig.1 or 2), the light unit will turn on, indicating the lighting system and
motion detection mode are activated for illumination. At daytime condition to test this unit, user can simulate nighttime condition by cover the
solar panel with a large size cardboard. Once the solar panel been covered, the light will immediately turn on; then remove the cardboard the
light will turn off automatically as photo cell function. If the light function as described above, the light is function normal and will provide
all-night-long illumination with SMART lighting profile during nighttime after fully charged.
SMART lighting profile:
Under eLEDing’s software-based Intelligent Power Management (IPM) system, the innovative SMART lighting
profile offers Dusk-to-Dawn lighting capability. It offers auto compensation during critical weather within different geographic locations.
During nighttime, the light will automatically activated when the ambient light is lower than 10 LUX, and keep lighting with maximum
brightness for the first 5 hours for most traffic period timing window, and then automatically dim to 20% of full brightness for energy-saving
purpose. Once motion being detected within saving mode period, the light will automatically come up to maximum brightness for 30 seconds
and back to dimming profile when motion disappear. If motion continues, the light will keep lighting with maximum brightness. (Fig. 3, 4)
Installation Guidelines
1. Follow above standard setup procedure to activate the lighting system (Fig.1 or 2)
2. Securely mount the unit on the light pole, adjust the light head direction based on your need (Fig.5)
3. The light will automatically shut down and charge during daytime sunshine condition
4. Suggested Mounting Height: 15-20 ft
5. Diameter of Mounting Adaptor: EE850W-SH30 (3"); EE860W-SH40 (3"); EE870W-SH50 (3-3/8"); EE880W-SH60 (3-3/8”), refer (Fig. 7)
6. Fixed light head angle to ground: 15 degrees or by fixed MFC
7.
Solar Panel Direction:
The solar panel must be mounted in a non-obstructed position where it will receive an average of at least 5 hours
daily direct sunlight all year round. For Northern hemisphere installations the solar panel can be mounted facing to East-South-West with
direct southerly facing position is best and visa-versa for Southern hemisphere installation. As a option as required, AUX DC power sources
can be use either for quickly charge light unit before installation, or/and for poor sunshine location or position with back-up power source or
as a charging enhancement method (Fig. 6)
8.
Solar Panel Maintenance:
Use a soft wet cloth to periodically (at least once a one year) clean the solar panel to avoid the reduction of
energy output due to accumulated dust. Clean accumulated snow as soon as possible during the snowing season.
e
L
E
D
in
g
Fig.3
Fig.6 Option
YouTube Video References:
- Initial Setup:
https://youtu.be/v631fTYvHqk
(Patented Technology)
Fig.1
Fig.2
Fig.3
Fig.5
