ElectroCraft SCA-LE-30-03 User Manual Download | Manualshive

Page: 1 / 32

background image

User Manual SCA-LE-30-03

ElectroCraft

®

E-Mail: [email protected] www.electrocraft.com May 2009

1

For Brush-Commutated DC Motors up to 75 W

SCA-LE-30-03

•

Servo amplifier in a rugged aluminium housing

•

Different methods of mounting for fast installation

•

Inputs and outputs via screw terminals

•

Operation mode setting with jumpers

•

User adjustable current limit

•

Wide range supply voltage b11 and +30 VDC for different kinds of DC-
power supplies

•

Protected against overtemperature and over-current

•

Linear amplifier

•

Continuous current up to 6 A

Basic drive description: The SCA-LE-30-03 servo amplifiers are designed to drive DC
brush type motors. They require a single DC power supply for operation. The drives are to
be used with a single motor. They have the functionality to operate as an independent
speed control or high performance servo. The drives are protected against short circuits,
under voltage, over temperature, and over current. It has multiple modes of operation and
serves as a reliable choice for your motion control needs.

4–Q Linear Servo – 03 A

1
2
3
...
»

Summary of Contents for SCA-LE-30-03

































Reviews:

No comments

Related manuals for SCA-LE-30-03

Brand: ThyssenKrupp Pages: 52

Brand: Fastech Pages: 26

Brand: Ltech Pages: 7

Brand: Vescent Photonics Pages: 18

Brand: Robotis Pages: 22

CACR-HR BAB Series

Brand: YASKAWA Pages: 293

Brand: ZIEHL-ABEGG Pages: 105

Brand: Fagor Pages: 386

ACH580-01 Series

Brand: ABB Pages: 76

ACS880-01 Series

Brand: ABB Pages: 16

Brand: YASKAWA Pages: 54

Brand: TCi Pages: 2

ACQ580-P Series

Brand: ABB Pages: 28

DB1-122D3 Series

Brand: Eaton Pages: 7

BHSS-2500W-PARA

Brand: Bholanath Pages: 22

Brand: D+H Pages: 16

Brand: WITTUR Pages: 36

Brand: SCHUNK Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands