background image

CHAPTER - 34 HIGHLIGHTS

(Summary of Changes)

Revision No. TR34-21 Sep 30/20

TO: HOLDERS OF THE AIRCRAFT MAINTENANCE MANUAL (06-117751)

Pages that have been added or revised are summarized below. Remove and insert the affected
pages as listed, and enter the above revision number with issue date into the Record of Revisions
sheet.

This Temporary Revision incorporates and supersedes previously released temporary
revisions for the chapters listed below.

Do not remove this page. Keep it in place as a record of previous changes.

CH/SE/SU

Page Block No.

Description of Change

34-10-00

PgBlk 501

Adjustment / Test - Added Standby Pitot/Static Verification with Standby
Display Unit (SDU).

34-10-10

PgBlk 401-Rem

(C)

Added MB 500-34-028 to effectivity for Pitot/AOA Probe auxiliary heaters -
Removal - Config C.

34-10-10

PgBlk 401-Inst

(C)

Added MB 500-34-028 to effectivity for Pitot/AOA Probe auxiliary heaters -
Installation - Config C.

34-40-50

PgBlk 1 (A)

Description and Operation – Config A. Corrected effectivity.

34-40-50

PgBlk 1 (B)

Description and Operation – Config B. Added configuration B – POST SB
500-31-024.

34-40-50

PgBlk 501 (A)

Adjustment/Test – Config A. Corrected effectivity.

34-40-50

PgBlk 501 (B)

Adjustment/Test – Config B. Added configuration for Stormscope lightning
strike test post SB 500-31-024.

34-50-10

PgBlk 1 (B)

Description and Operation - Revised Effectivity (ALL POST MB
500-31-018). Revised Description.

34-50-10

PgBlk 201 (A)

Description and Operation - Revised Effectivity (ALL POST MB
500-31-018). Updated for ADS-B Out – Config A.

34-50-10

PgBlk 201 (B)

Added GPS 3 (GDL 88) Maintenance Practices – Config B.

34-50-10

PgBlk 501 (C)

Adjustment/Test for GPS Units – Config C.

34-50-11

PgBlk 401-Rem

(C)

Added GPS 3 (GDL 88) Unit Removal procedure.

EA500 Aircraft Maintenance Manual — 06-117751

Temporary Revision No. 34-21

34-HIGHLIGHTS

Page 1

Sep 30/20

© 2020 Eclipse Aerospace, Inc.

Summary of Contents for EA500

















































































































































































































































































































Reviews: