INSTALLATION
MOUNTING:
1. Mount the cover module in its support position.
• Ceiling and wall mount: mark and drill desired location on mounting
surface. Secure with 1/4” (6mm) bolts or lag screws (not
provided).
• Pendant, cone, stanchion mount: securely thread onto the
appropriate NPT size conduit. Tighten set screw located in the
conduit hub. See Figure 1.
• Eaton’s Crouse-Hinds HTL thread lubricant must be added to the
conduit threads to prevent water from entering the luminaire.
Set screw
Open
hinge
Ground wires
FIGURE 1
WARNING
To avoid the risk of fire, explosion or electric shock, this product
should be installed, inspected and maintained by a qualified
electrician only, in accordance with all applicable electrical codes.
WARNING
To avoid electric shock:
Be certain electrical power is OFF before and during installation and
maintenance.
Luminaire must be supplied by a wiring system with an equipment
grounding conductor.
To avoid burning hands:
Make sure lens and housing are cool when performing
maintenance.
WARNING
To avoid explosion:
Make sure the supply voltage is the same as the luminaire voltage.
Do not install where the marked operating temperatures exceed
the ignition temperature of the hazardous atmosphere.
Do not operate in ambient temperatures above those indicated on
the luminaire nameplate.
Use proper supply wiring as specified on the luminaire nameplate.
All gasket seals must be clean.
Before opening, electrical power to the luminaire must be turned
off. Keep tightly closed when in operation.
To reduce the risk of ignition due to electrostatic discharge, avoid
contact with the luminaire while explosive atmosphere is present.
Clean only with damp cloth.
WIRING:
1. Pull field wiring into cover module.
2. Close all unused conduit entries with conduit plugs provided. To
prevent galling and to ensure watertightness, lubricate conduit
plugs with Eaton’s Crouse-Hinds HTL lubricant before installing,
and secure wrench-tight with at least five (5) full threads engaged
(42-52 ft.-lb. for 3/4” plugs, and 58-68 ft.-lb. for 1” plugs).
3. Hang LED luminaire on the cover module hinge hook.
4. Connect supply wires to luminaire wire leads or terminal block per
the attached wiring diagrams using methods that comply with all
applicable codes. See Figure 2. Tighten all electrical connections.
5. Close driver housing onto cover module, making sure that all wires
are safely inside driver housing. Tighten captive closing screw to
30 in.-lbs. (3.4 N-m). Ensure two (2) bosses on driver housing are
in contact with cover module.
6. Turn power on.
IF 1912 • 08/21
Copyright © 2021, Eaton’s Crouse-Hinds Division
Page 1
Champ VMVL and PVML high lumen LED luminaires
Installation & maintenance information
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IF 1912
APPLICATION
Champ® VMVL/PVML Series 13, 17, 21, 25,17-M2, 21-M2, 25-M2
Champ
®
VMVL luminaires are suitable for use in certain hazardous
(classified) areas as defined by the National Electrical Code (NEC
®
).
Champ
®
PMVL luminaires are not suitable for use in these NEC
classified areas.
Refer to the luminaire nameplate for specific classification information,
maximum ambient temperature suitability and corresponding operating
temperature (T-code).
Luminaire construction is designed for use indoors and outdoors in
marine and wet locations, where moisture, dirt, corrosion, vibration
and rough usage may be present.
FIGURE 2
IF 1912 • 08/21
Copyright © 2021, Eaton’s Crouse-Hinds Division
Page 2
Input voltage:
UNV1
• 100-277 VAC, 50/60 HZ NEC
• 100-240 VAC, 50/60 HZ EN/IEC
• 127-250 VDC
UNV34
• 347-480 VAC, 50/60 HZ NEC/CEC
NEC/CEC
• Class I, Division 2, Groups A, B, C, D
• Class II, Groups E, F, G
• Class III
• Class I, Zone 2 AEx ec mb IIC (UNV1 Only)
• Ex ec mb IIC Gc (UNV1 Only)
• Zone 21 AEx/Ex tb IIIC Db (UNV1 Only)
• Simultaneous Presence
• Wet Locations, Type 4X
UL standards
• UL 844 Hazardous (Classified)
• UL1598 Luminaires, UL1598A Marine
CSA standard
• CSA C22.2 No. 137
IEC/ATEX standards (UNV1 Only)
• IEC 60079-0, 7th Edition / EN IEC 60079-0:2018
• IEC 60079-7:2010, 5.1 Edition / EN 60079-7:2015
• IEC 60079-31:2008, 2nd Edition / EN 60079-31:2014
• IEC 60529:2001 / EN 60529:2001
• IEC 60598-1:2008 / EN 60598-1:2008
• IEC 60598-2:2008 / EN 60598-2:2008
• IEC 60079-18:2017, 4.1 Edition / EN 60079-18:2015 +
A1:2017
Luminaire markings (UNV1 Only)
• IECEx UL 14.0031X
• DEMKO 14 ATEX 1324722X
• DEMKO 14 ATEX 2274231X
100-277 VAC/127-250 VDC (UNV1 base luminaire
only)
II 3 G EX ec mb IIC T* Gc -40°C to +40°C
II 3 G EX ec mb IIC T* Gc -40°C to +55°C
II 3 G EX ec mb IIC T* Gc -40°C to +65°C
II 2 D Ex tb IIIC T**°C Db -40°C to +40°C
II 2 D Ex tb IIIC T**°C Db -40°C to +55°C
II 2 D Ex tb IIIC T**°C Db -40°C to +65°C
Input voltage:
UNV1
• 100-277 VAC, 50/60 HZ
• 127-250 VDC
UNV34
• 347-480 VAC, 50/60 HZ
Certifications & compliances
• Wet location, Type 4X
• IP66
UL standards
• UL1598 Luminaires, UL1598A
Marine
• UL8750
• UL50, UL50E
CSA standard
• CSA C22.2 No. 250.0-08
IEC standard (UNV1 Only)
• IEC 60598
VMVL 13 through 25:
PVML 13 through 25:
For EMC compliance:
If the dimming interface of the LED driver are connected to an external dimmer which is not provided with the luminaire, a ferrite core must be
used on the input and dimming lines. Approved ferrite cores are Fair-Rite P/N 0431167281.
THIRD ANGLE PROJECTION
WIRING DIAGRAM
13 UNV34
OUTPUT
INPUT
N
L
SPLICE CONNECTORS (x2)
CUSTOMER TERMINATION
G
DRIVER
LED PCB
CONNECTIONS
BLACK- ORANGE
BLACK-WHITE
BLACK
RED
VIOLET
DIM +
DIM -
GREY
GROUND CASE
BY FASTENING
DRIVER
COMPARMENT
GROUND
INPUT
OUTPUT
GROUND CASE
BY FASTENING
DIM -
DIM +
BLACK
RED
VIOLET
GREY
RED
BLACK
GREY
VIOLET
GROUND CASE
BY FASTENING
BLACK-WHITE
BLACK-ORANGE
DRIVER
G
CUSTOMER TERMINATION
LED PCB
CONNECTIONS
OUTPUT
INPUT
N
L
SPLICE CONNECTIONS (x4)
DRIVER
WIRING DIAGRAM
17
,
21
,
25 UNV34
DRIVER
COMPARMENT
GROUND
SPLICE
CONNECTOR
DRIVER
COMPARTMENT
GROUND
YELLOW
VIOLET
GREY
BLACK
RED
DIM-
DIM+
VAUX
DIM-
DIM+
VAUX
RED
BLACK
GREY
VIOLET
YELLOW
GREEN/YELLOW
BLUE
BROWN
CUSTOMER TERMINATION
WIRING DIAGRAM
13
,
17, 21 and 25
UNV1
L
N
G
OUTPUT
INPUT
OUTPUT
INPUT
DRIVER
LED PCB
CONNECTIONS
SPLICE
CONNECTORS (x4)
DRIVER
13L-25L WIRING DIAGRAMS
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT.
SCALE 1:8
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 1 OF 1
CODE ...
THIRD ANGLE PROJECTION
WIRING DIAGRAM
13 UNV34
OUTPUT
INPUT
N
L
SPLICE CONNECTORS (x2)
CUSTOMER TERMINATION
G
DRIVER
LED PCB
CONNECTIONS
BLACK- ORANGE
BLACK-WHITE
BLACK
RED
VIOLET
DIM +
DIM -
GREY
GROUND CASE
BY FASTENING
DRIVER
COMPARMENT
GROUND
INPUT
OUTPUT
GROUND CASE
BY FASTENING
DIM -
DIM +
BLACK
RED
VIOLET
GREY
RED
BLACK
GREY
VIOLET
GROUND CASE
BY FASTENING
BLACK-WHITE
BLACK-ORANGE
DRIVER
G
CUSTOMER TERMINATION
LED PCB
CONNECTIONS
OUTPUT
INPUT
N
L
SPLICE CONNECTIONS (x4)
DRIVER
WIRING DIAGRAM
17
,
21
,
25 UNV34
DRIVER
COMPARMENT
GROUND
SPLICE
CONNECTOR
DRIVER
COMPARTMENT
GROUND
YELLOW
VIOLET
GREY
BLACK
RED
DIM-
DIM+
VAUX
DIM-
DIM+
VAUX
RED
BLACK
GREY
VIOLET
YELLOW
GREEN/YELLOW
BLUE
BROWN
CUSTOMER TERMINATION
WIRING DIAGRAM
13
,
17, 21 and 25
UNV1
L
N
G
OUTPUT
INPUT
OUTPUT
INPUT
DRIVER
LED PCB
CONNECTIONS
SPLICE
CONNECTORS (x4)
DRIVER
13L-25L WIRING DIAGRAMS
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT.
SCALE 1:8
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 1 OF 1
CODE ...
THIRD ANGLE PROJECTION
WIRING DIAGRAM
13 UNV34
OUTPUT
INPUT
N
L
SPLICE CONNECTORS (x2)
CUSTOMER TERMINATION
G
DRIVER
LED PCB
CONNECTIONS
BLACK- ORANGE
BLACK-WHITE
BLACK
RED
VIOLET
DIM +
DIM -
GREY
GROUND CASE
BY FASTENING
DRIVER
COMPARMENT
GROUND
INPUT
OUTPUT
GROUND CASE
BY FASTENING
DIM -
DIM +
BLACK
RED
VIOLET
GREY
RED
BLACK
GREY
VIOLET
GROUND CASE
BY FASTENING
BLACK-WHITE
BLACK-ORANGE
DRIVER
G
CUSTOMER TERMINATION
LED PCB
CONNECTIONS
OUTPUT
INPUT
N
L
SPLICE CONNECTIONS (x4)
DRIVER
WIRING DIAGRAM
17
,
21
,
25 UNV34
DRIVER
COMPARMENT
GROUND
SPLICE
CONNECTOR
DRIVER
COMPARTMENT
GROUND
YELLOW
VIOLET
GREY
BLACK
RED
DIM-
DIM+
VAUX
DIM-
DIM+
VAUX
RED
BLACK
GREY
VIOLET
YELLOW
GREEN/YELLOW
BLUE
BROWN
CUSTOMER TERMINATION
WIRING DIAGRAM
13
,
17, 21 and 25
UNV1
L
N
G
OUTPUT
INPUT
OUTPUT
INPUT
DRIVER
LED PCB
CONNECTIONS
SPLICE
CONNECTORS (x4)
DRIVER
13L-25L WIRING DIAGRAMS
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
A
B
C
D
1
2
3
4
5
6
7
8
A
D
C
B
8
7
6
5
4
3
2
1
Your name
ASSY2
CAT2
CAT1
ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1
.3
INCHES.
rev
0000000
WT.
SCALE 1:8
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm
in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 1 OF 1
CODE ...
WIRING DIAGRAM
13, 17, 17-M2, 21, 21-M2, 25, 25-M2 UNV1
WIRING DIAGRAM
13 UNV34
WIRING DIAGRAM
17, 17-M2, 21, 21-M2, 25, 25-M2 UNV34
